Mechanical Engineering Archive: Questions from September 30, 2023
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
Encuentre el valor del torque de entrada en la manivela del mecanismo mostrado en la figura en el entendido de que los centros de masa de cada eslabón se ubican en \( G_{2}, G_{3} \) y \( G_{4} \) re0 answers -
Las manivelas 2 y 4 del mecanismo de cuatro barras representado están balanceadas, las dimensiones del eslabonamiento son: \( \mathrm{O}_{2} A=6 \) pul, \( A B=18 \) pul, \( A G=12 \) pul, \( A C=240 answers -
Solve the initial value problem \[ \begin{array}{l} \frac{\mathrm{d}}{\mathrm{d} x} y(x)+5 x^{4} y(x)=-5 \mathrm{e}^{\left(-x^{5}\right)} ; y(0)=1 \\ y(x)=\mid \text { 回 } \end{array} \]1 answer -
ejercicio de mecanica de fluidos
3. Agua fluye por un sifón a un caudal de \( 0.02 \mathrm{~m}^{3} / \mathrm{s} \) el diámetro del conducto es de \( 50 \mathrm{~mm} \), para una \( \mathrm{h}=0.5 \mathrm{~m} \) determinar la presiÃ1 answer -
ejercicio de mecanica de fluidos
4. Una tuberÃa de \( 5 \mathrm{~m} \) de longitud puede ser orientada a cualquier ángulo \( \theta \), considerando las perdidas en la tuberÃa encuentre la distancia horizontal del chorro la base d1 answer -
ejercicio de mecanica de fluidos
Determine la altura de la bomba \( H_{B} \) si en el siguiente sistema se bombea agua a \( 20^{\circ} \mathrm{C} \) hasta un depósito, el flujo es \( 54 \mathrm{~m}^{3} / \mathrm{h} \). En la aspirac1 answer -
ejercicio de mecanica de fluidos
2. Calcule la presión de aire en el tanque sellado que provocara que la velocidad del flujo sea de \( 20 \mathrm{ft} / \mathrm{s} \) a la salida de la tobera, considerar \( \mathrm{h}=10 \mathrm{ft}1 answer -
ejercicio de mevanica de fluidos
1. Determinar el flujo de aceite a la salida de la tobera y las presiones en A y B1 answer -
La armadura de arrastre interna para el ala de un avión ligero está sometida a las fuerzas que se muestran. Determine la fuerza en los elementos BC, BH y HC, y establezca si los elementos están en
a armadura de arrastre interna para el ala de un avión ligero está sometida a las fuerzas que se muestran. Determine la uerza en los elementos BC, BH y HC, y establezca si los elementos están en te1 answer -
ejercicio de mevanica de fluidos
Dos puntos de una red de tuberÃa de cobre conducen aceite \( \left(v=4.42 \times 10^{-6} \mathrm{~m}^{2} / \mathrm{s}\right) \) la longitud total de la tuberÃa es de \( 1200 \mathrm{~m} \) y su diá1 answer -
ejercicio de mevanica de fluidos
Determinar el diámetro de una tuberÃa de fundición (cast iron) cuya longitud es de \( 2400 \mathrm{~m} \) y debe transportar \( 1 \mathrm{~m}^{3} / \mathrm{s} \) de agua \( \left(v=1.12 \times 10^{1 answer -
ejercicio de mecanica de fluidos
7. La instalación de la Figura 2 presenta \( 28 \mathrm{~m} \) de conducto de diámetro \( 50 \mathrm{~mm}, 22 \mathrm{~m} \) de diámetro \( 150 \mathrm{~mm} \) y \( 46 \mathrm{~m} \) de diámetro \1 answer -
can you send answers details?
P1.1. El sistema de tuberÃas en paralelo de la figura, ¿cómo repartirá un caudal de agua de Q \( =456 \mathrm{I} / \mathrm{s} \) entre sus dos ramas? ¿Cuál es la pérdida de carga entre A y B? D1 answer -
For the following pumping system the losses due to friction in the suction pipe are and for the discharge pipe are The pump efficiency is 85%. The efficiency of the electric motor is 90%. The water
\( \frac{3\left(V_{\text {des }}\right)^{2}}{2 g} \) \( \frac{4\left(V_{a s p}\right)^{2}}{2 g} \) \( 1.0(35 \%) \) Para el siguiente sistema de bombeo, las pérdidas debido a fricción en la tube0 answers -
1.El perfil mostrado en la figura se somete a la acción de un momento de flexión de \( 250 \mathrm{Nm} \) en la dirección que muestra la figura, determine el esfuerzo de flexión producido en \( \m1 answer -
0 answers
-
1. Una viga simplemente apoyada en sus extremos tiene la sección recta y las cargas indicadas en la figura. Si el esfuerzo normal máximo no debe exceder de \( 120 \mathrm{MPa} \), determinar el valo1 answer -
En la figura se muestra un mecanismo que está formado por otros tres: un manivela-biela-corredera, un cuatro barras y un manivela-biela-corredera descentrado. Utilizando métodos de fórmulas calcule
\begin{tabular}{|l|} \hline \( \mathrm{O}_{2} A=50.8 \mathrm{~mm} \) \\ \hline\( A C=102 \mathrm{~mm} \) \\ \hline\( A B=44.5 \mathrm{~mm} \) \\ \hline\( B C=63.5 \mathrm{~mm} \) \\ \hline\( B D=50.80 answers -
1 answer
-
I want you to explain in detail how you obtain acceleration. Only that
20-55. En el instante que se muestra, la base del brazo robótico gira alrededor del eje \( z \) con una velocidad angular de \( \omega_{1}=4 \mathrm{rad} / \mathrm{s} \), la cual se está incrementan1 answer