Mechanical Engineering Archive: Questions from November 30, 2023
-
las funciones potenciales y exponenciales, con el empleo de logaritmos se las transforma en funciones lineales y se las resuelve aplicando regresión lineal, y los valores desconocidos de las funcione
Variantes de la regresión lineal - La función potencial \[ y=c \cdot x^{a} \] Se puede trasformar en \[ \log y=a \log x+\log c \] Si usamos las nuevas variables \( X=\log x \) e \( Y=\log y \), obte1 answer -
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
A piping system transports a fluid with an internal pressure of 1500 kPa (figure 1). In addition to being subject to fluid pressure, the pipe supports a vertical load of 9 kN and a horizontal load of
Un sistema de tuberías transporta un fluido con una presión interna de \( 1500 \mathrm{kPa} \) (figura 1). además de estar sujeta a la presión del fluido, la tubería soporta una carga vertical de0 answers -
Problema 3 (30 Puntos): Se desea modelar la dinámica de control de un vehículo de reparto, el cual se representa mediante una barra rígida (modela el chasis), con masa \( m \) y momento de inercia0 answers -
7.20 Un tubo de acero con 12 in. de diámetro exterior se fabrica a partir de una placa con \( \frac{1}{4} \) in. de espesor, la cual se suelda a lo largo de una hélice que forma un ángulo de \( 22.1 answer -
6.4 Tres tablas, cada una de 2 in. de espesor, se clavan para formar una viga sometida a un cortante vertical de \( 300 \mathrm{lb} \). Si se sabe que la fuerza cortante permisible en cada clavo es de1 answer -
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
F=50lb , Theta =35 Dibuja el diagrama de fuerza cortante y momento flector para las siguientes vigas0 answers
-
0 answers
-
1 answer
-
1 answer
-
Realizar el siguiente ejercicio
2. Expresar la función de transferencia \( T(s)=\frac{C(s)}{R(s)} \) del siguiente diagrama de bloques, \( \mathrm{G}(\mathrm{s}) \) se toma del punto 1 . 3. A partir de la siguiente función de tran0 answers -
0 answers
-
help!
PUNTO 8 [1P] Una barra de acero de diámetro \( \boldsymbol{d} \) se encuentra insertada una longitud I en una pared como se muestra en la figura. Con el propósito de extraer la barra, se ejerce una1 answer -
Considerando que una viga empotrada está fabricada con un material cuyo E=200GPa y tiene un momento de inercia l=65x10-6 mm*6. Determine lo siguiente: A) diagrama de cuerpo libre y calculo de condici
Considerando que una viga empotrada está fabricada con un material cuyo \( E=200 \mathrm{GPa} \) y tiene un momento de inercia \( \mathrm{l}=65 \times 10-6 \mathrm{~mm} * 6 \). Determine lo siguiente1 answer -
help!
PUNTO \( 14[2 \mathrm{P}] \) Para la sección \( \mathbf{T} \) mostrada a continuación, calcule la relación \( \left(\tau_{s} / \tau_{i}\right) \), donde \( \tau_{s} \) es el esfuerzo cortante justo1 answer -
Una polea multiple esta sujeta a distintas tensiones. ¿Cual debera ser el valor de la fuerza de tension “P”, si el momento resultante con respecto al punto A vale cero?
Una porta múltiple está sujeta a distintas tensiones. ¿cuál debera ser el valor \( \alpha \) e la fueriza de tensión " \( P \) ", si el momento resultante con respecto al punto " \( A \) " vale c1 answer -
1 answer
-
Problem 3 Calculate the speed of the current necessary to produce a Reynolds number of 107 for the current on a square plate of 1 m on the side, with the following fluids: (a) water at 20 ° C, (b) a
Problema 3 Calcúlese la velocidad de la corriente necesaria para producir un número de Reynolds de \( 10^{7} \) para la corriente sobre una placa cuadrada de \( 1 \mathrm{~m} \) de lado, con los flu1 answer -
1 answer
-
help!
PUNTO 12 [1P] Una claraboya hemisférica en una cámara de descompresión está sometida a una presión de aire interna de 90 psi. El esfuerzo de tensión en la ventana si el radio del hemisferio es d1 answer -
1 answer
-
1) Traza los diagramas de fuerza cortante y de momento flector, indica los valores máximos de la fuerza cortante y el momento flector.1 answer -
1 answer
-
)etermina el valor de las fuerzas que actúan en todos los elementos de la armadura; indica si los lentos están en tensión o en compresión. \( \mathrm{P}=40 \mathrm{kN} \) y F \( =20 \mathrm{kN} \)1 answer -
1 answer
-
1 answer