Mechanical Engineering Archive: Questions from November 29, 2023
-
1 answer
-
En una planta generadora hidroeléctrica, el agua entra a las toberas de la turbina a \( 750 \mathrm{kPa} \) de presión absoluta, con una velocidad baja. Si las salidas de las toberas están expuesta1 answer -
1 answer
-
1 answer
-
0 answers
-
0 answers
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
For the effort shown, determine the following using the equations: a. The main efforts. b. The maximum shear stress and its corresponding normal stress value. c. Check the calculated values at points
Problema No.1: Para el estado de esfuerzo mostrado, determine por medio de las ecuaciones lo siguiente: a. Los esfuerzos principales b. EL esfuerzo cortante máximo y su correspondiente valor de esfue1 answer -
1 answer
-
Verify that the beam section AA' shown can withstand applied loads knowing that the allowable normal stress is equal to 65 MPa. Consider that the critical point is at point P of the cross section.
Problema No.2: Verifique que en la sección \( A-A^{\prime} \) de viga mostrada puede soportar las cargas aplicadas sabiendo que el esfuerzo normal permisible es igual a \( 65 \mathrm{MPa} \). Conside1 answer -
1. El balancín \( \mathrm{OA} \) de la figura rueda sin deslizarse sobre la superficie horizontal. En la posición mostrada, la velocidad angular del balancín es de \( 7 \mathrm{rad} / \mathrm{s} \)0 answers -
I) La barra delgada homogénea \( \mathrm{AB} \) de \( 20 \mathrm{~kg} \) se suelta a partir del reposo en la posición indicada. Calcule la aceleración angular de la barra y la tensión en la cuerda1 answer -
La bala de \( 8.00 \mathrm{~g} \) de masa se incrusta en la varilla delgada de \( 6.00 \mathrm{~kg} \) en el punto indicado. Un sensor detecta una velocidad angular de la barra de \( 0.331 \mathrm{rad1 answer -
Se desea realizar el circuito de control de un proceso que funciona de la siguiente manera: 1. Al dar la señal de arranque se activa el sistema. 2. Si sucede una sobrecarga en cualquiera de los motor0 answers -
help!
PUNTO 9 [2P] Calcule el máximo momento de flexión en la viga. (Nota: en este problema se deben dibujar y rotular correctamente los diagramas de momento y cortante interno).1 answer -
help!
PUNTO 11 [3P] El motor mostrado en la figura rota a \( 1780 \mathrm{rpm} \), y entrega 15 kW al engranaje en \( D \). Los diámetros de los ejes son \( \mathrm{d}_{1}=20 \) \( \mathrm{mm} \) y \( \mat1 answer -
help!
PUNTO \( 10[2 \mathrm{P}] \) Una barra homogénea \( \mathbf{A B} \) está fija entre paredes rígidas en los extremos \( \mathbf{A} \) y \( \mathbf{B} \) como se muestra en la figura. Todo el sistema1 answer -
\begin{tabular}{ll} \begin{tabular}{l} Teniendo en cuenta el modelo del servo \\ obtenido en el primer examen y el \end{tabular} & \( \mathrm{PID}=\mathrm{PI} \) controller \( \quad D(s)=\frac{s+0.6}{0 answers -
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
Calcula la velocidad angular de cada uno de los engranes y justifica por medio de ecuaciones de movimiento dependiente, si el sistema se mueve por medio de un motor eléctrico de 5 volts con \( 6000 \1 answer -
1 answer
-
1 answer
-
Una esfera de radio \( r=6 \mathrm{~cm} \) y peso de \( 100 \mathrm{~N} \) se cuelga de la esquina de un cuarto por medio del cable \( A B \) de \( 10 \mathrm{~cm} \) de longitud, según se muestra en1 answer -
Determine la inercia, con respecto al eje centroidal X. De su respuesta en pulgadas.
\( \begin{array}{l}\mathrm{a}=18 \mathrm{in} \\ \mathrm{b}=41 \mathrm{in} \\ \mathrm{c}=4 \mathrm{in}\end{array} \)1 answer -
Determina los diagramas de cortante y momento de la viga sujeta a las cargas mostradas en la figura.1 answer