Mechanical Engineering Archive: Questions from March 17, 2023
-
1 answer
-
1 answer
-
1 answer
-
1) Determinar las fuerzas internas en los elementos de cada una de las cerchas, indicar si están a compresión o a tensión, use el método de los nudos. a) b 1) Determine the internal forces in the2 answers -
The load F shown in the figure has a magnitude of F= 73590 N. The rod shown has a cross-sectional area of 500 mm² The modulus of elasticity of the rod is 200 GPa. Determine the displaceme
La carga \( F \) mostrada en a figura tiene una magnitud de \( F=73590 \mathrm{~N} \). La vara mostrada tiene un área cros-secdional de 500 mm² \( ^{2} \). 8 mbstulo se elsisticises de la vara es de2 answers -
Argumente ¿Qué está pasando con el gas en el proceso de b →c? a) Responde con una descripción de sus variables de estado (variables termodinámicas). b) Explica si hay entrada o salida de calor
Un centro de diseño automotriz, está valorando la construcción de una nueva máquina de combustión para autos autónomos. El cilindro del motor ocupa en cada ciclo, 1.624 moles de un gas ideal par0 answers -
3. Si le indican que debe diseñar las barras de la estructura del dibujo para soportar la carga mostrada, A) ¿Qué datos debería usted conocer, aparte de los indicados? B) Explique las razones de s2 answers -
The shaft with a fillet radius of 2.8 mm is subjected to the torques shown in the figure of which TA = 173 N-m. Determine what is the maximum stress in the figure. Assume that the same occurs in the f
El eje con un fillet de radio de \( 2.8 \mathrm{~mm} \) está sujeto a los torques mostrados en la figura de los cuales \( \mathrm{TA}=173 \mathrm{~N}-\mathrm{m} \). Determine cual es el estres máxim2 answers -
2 answers
-
0 answers
-
El eje con un fillet de radio de \( 2.8 \mathrm{~mm} \) está sujeto a los torques mostrados en la figura de los cuales \( \mathrm{T}_{\mathrm{A}}=208 \mathrm{~N}-\mathrm{m} \). Dotemine cual es el es0 answers -
1 answer
-
1 answer
-
1 answer
-
0 answers
-
El eje con un Filit de fadio de \( 2 . \mathrm{B} \mathrm{mm} \) eshl sujeto a los torques motrados en la figura de lon cuales \( T_{\mathrm{A}}=160 \mathrm{~A}=\mathrm{m} \).2 answers -
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
Suppose a ladder is flown like the one shown below, using what we learned in the stress and deformation analysis course, model the ladder to support a person weighing up to 150kg. Consider the followi
Suponga una escalera volada como la mostrada a continuación, usando lo aprendido en el curso de análisis de esfuerzos y deformaciones, planté la modelación de dicha escalera para soportar que suba0 answers -
6. Se desea transmitir movimiento, con el mismo sentido de giro, entre dos ejes paralelos situados a \( 60 \mathrm{~cm} \). De distancia. Para ello se emplean dos poleas al sistema una tiene un diáme2 answers -
1 answer
-
1 answer
-
1 answer
-
Los dos ejes sólidos y engranes mostrados son usados para transmitir \( 32 \mathrm{hp} \) desde el motor en A operando a una velocidad de \( 1260 \mathrm{rpm} \) a una máquina herramienta en D. Cono2 answers -
1 answer
-
Los dos ejes están fabricados de acero A-36. Cada uno tiene un diámetro de 2 in y se apoyan en los cojinetes A, B y C, que permiten su rotación libre. Si el apoyo en D está fijo, determine el áng2 answers -
1 answer
-
Bajo condiciones normales de carga, el motor eléctrico ejerce un torque de 12 kips-in en \( E \). Conociendo que cada eje es sólido determine el córtante máximo en a) eje \( B C \), b) eje \( C D,2 answers -
0 answers
-
3.9 La pieza mostrada es elaborada en acero con \( E=200 \mathrm{GPa} \). Los elementos \( \mathrm{AB} \) y \( \mathrm{DE} \) tiene unárea de \( 30 \times 10 \mathrm{~mm}^{2} \). Determinar el despla2 answers -
0 answers