Mechanical Engineering Archive: Questions from June 09, 2022
-
1 answer
-
Answer the question down below:
Determine los índices de Miller de la dirección A 21.- de ser precisa. 5 pts c/u. B del plano B La notación debe1 answer -
1 answer
-
A mechanical part requires 2,100 units per day of all parts, and these parts weigh 1, 0.5, 9, 5, 15, and 3.75 pounds, respectively. Each machine is identified by a letter (R, A, B, C, D, E, F, G and S
2. Para una pieza mecánica se necesitan 2,100 unidades por día de todas las partes, y éstas pesan 1, 0.5, 9, 5, 15 y 3.75 libras, respectivamente. Cada máquina se identifica con una letra (R, A, B0 answers -
The component shown is very similar to a socket wrench that generates various stresses in the cantilever bar OABC. This bar is made of AISI 1035 CD steel. This component is assumed to have no value af
2 pulg. 1 pulg D. pulg R. 12 pulg 1 pulg D. 15 pulg Sección crítica B с pulg 1 pulg D. Tabla A-20 Resistencias determinísticas mínimas a la tensión y a la fluencia ASTM de algunos aceros lamina1 answer -
1 answer
-
1.- A die-cutting operation is going to be carried out on a 2 mm thick sheet of cold rolled steel (medium hardness). The part is circular with a diameter of 75 mm. The shear stress of the metal is 325
1.- Una operación de troquelado se va a realizar en una lámina de 2 mm de espesor de acero rolado en frío (dureza media). La parte es circular con un diámetro de 75 mm. El esfuerzo cortante del me1 answer -
1 answer
-
A bending operation will be performed on a 5 mm thick sheet of steel cold rolled. The figure shows the geometry and bending. Determine the size of the die cut needed (initial part).
2.- Una operación de doblado se realizará en una lámina de 5 mm de espesor de acero rolado en frío. La figura muestra la geometria y el dobado. Determine el tamaño del troquelado que se necesita1 answer -
600 10 1400 Pulido Maquinado o estirado en frio 300 Laminado en c 200 Tal como se forje 100 100 120 140 160 180 200 Resistencia a la tensión, (k) GURA 5-8 Resistencia a la fatiga x, en función de la1 answer -
1 answer
-
it is desired to obtain a hypoeutectoid steel with 42 HRC; propose tempering heat treatment; where 3 solid phases are formed. indicate the treatment conditions and the percentages of phases that will
3. (Valor 20 Puntos) Se desea obtener un acero hipoeutectoide con 42 HRC; proponga un tratamiento térmico de templado; donde se formen tres fases sólidas. Indique las condiciones del tratamiento y l1 answer -
Discuss the simply supported beam with cantilever; draw internal force diagrams and identify the absolute maximum shear force and the absolute maximum bending moment
1. (50 puntos) Analice la viga simplemente apoyada con voladizo; trace los diagramas de fuerzas internas e identifique la fuerza cortante máxima absoluta y el momento flexionante máximo absoluto. 11 answer -
Una planta de bombeo y almacenamiento usa una turbina para generar energía hidroeléctrica durante el día, permitiendo que el agua del depósito superior fluya a través de la turbina hacia el depó1 answer -
Para las condiciones mostradas en la figura, (a) Determine la fuerza hidrostática F sobre la compuerta triangular, que está articulada en el borde inferior y sostenida por la reacción RT en la esqu1 answer -
Determine the maximum normal stress and maximum shear normal stress in a section that is located 500 mm from the free end of the cantilever beam.
2. (50 puntos) Determine el esfuerzo normal máximo y el esfuerzo cortante máximo en una sección que se ubica a 500 mm del extremo libre de la viga en voladizo. 100 A 100 kN 500 mm 20 B 20 2 50 Acot1 answer