Electrical Engineering Archive: Questions from May 18, 2022
-
Part II (30 points): Suponga que la corriente de campo del generador del problema anterior se fija en un valor de 5 A. a) ¿Cuál será el voltaje en las terminales del generador si se conecta a una c1 answer -
Assemble the circuit of Figure 1 in TINKERCAD, the output of the OPAMP should model the following equation Y = 4X - 2 (Adder - Subtracter). Design criteria: VI= is the load voltage RL V2 = is variable
Montar el circuito de la figura 1 en Tinkertad, la salida del OPAMP debe modelar la siguiente ecuación Yaxsumador - Restador) Criterios para Diseñar: Vi-es el voltaje de la carga Rt. V2 es variable1 answer -
Encuentra el voltaje del capacitor, tal y como lo registra el voltimetro Vc. R1 R-1 kOhm L1 L-100 mH C1 CH4 nF W Lull I=2 A 1-20 kHz Phase=0 1 Vc HI:1 answer -
1 answer
-
Mounting the circuit of Figure 1 in Tinkercad and labeling each component, the OPAMP output must model the following equation Y = 4X - 2 (Sumer - Retractor). Criteria for Designing: V1= is the voltage
Montar el circuito de la Figura 1 en Tinkercad, la salida del OPAMP debe modelar la siguiente ecuación Y-4X-2 (Sumador-Restador). Criterios para Diseñar: V1-es el voltaje de la carga RL. V2 = es var1 answer -
In a 0.6H inductor there is a voltage of 8e^-8t volts with an initial current of -2A, what is the value of the current for the value of t= 0.25s
Pregunta 2 25 p En un inductor de 0.6 H se mide un voltaje de 8 e-t volts con una corriente inicial de -2 A, ¿Cuál es el valor de la corriente para t =0.25s?1 answer -
The following circuit has been connected for a long time. Calculate the value of the energy stored in the equivalent inductor and equivalent capacitor. The value of source A is 7.3 Volts. Write in the
Pregunta 1 25 pts El circuito siguiente lleva mucho tiempo conectado. Calcule el valor de la energía almacenada del inductor equivalente y el capacitor equivalentes. El valor de la fuente A es 7.3 Vo1 answer -
The following circuit has been connected for a long time, and the switch closes at t=0. If the value of source B is 29 volts, calculate the inductor current for t=0.19s.
25 pts Pregunta 3 El siguiente circuito ha estado conectado por mucho tiempo, y el interruptor se cierra en t=0. Si el valor de la fuente B es 29 volts, calcule la corriente del inductor para t= 0.191 answer -
The following circuit has been connected for a long time, and the switch moves from position (a) to (b) at t=0. If the value of source C is 12V, calculate the capacitor voltage at t=0.07.
Pregunta 4 25 pts El siguiente circuito lleva mucho tiempo conectado, y el interruptor se mueve de la posición (a) a (b) en t=0. Si el valor de la fuente C es 12 V, calcule el voltaje del capacitor e1 answer -
Calculate the value of the resistor so that the maximum power is transferred, and the value of this power, if the value of the voltage source is 7.1 volts. write in the solution in value of the power
Calcule el valor de la resistencia para que se se transfiera la máxima potencia, y el valor de esta potencia, si el val de la fuente de voltaje es 7.1 volts. (Escriba en la solución en valor de la p1 answer -
The charge density ρ s = 3x2 – 9xy, find the total charge in the region defined by 0 < and < x2, -2 < x < 2
La densidad de carga p₁ = 3x²9xy, encuentre la carga total en la región definida por 0 < y < x², -2 < x < 2 Select one: O a. 19.2 O b. -36.0 O C. 38.4 O d. -144 O e. 1921 answer -
Determine the magnitude of electrical flow at (0, 0, 5 m) given two charging points of 17 μC at (4 m, 0, 0) and (-4 m, 0, 0).
Determine la magnitud de flujo electrico en (0, 0,5 m) dado dos puntos de carga de 17 µC en (4 m, 0, 0) y (-4 m, 0, 0). Select one: O a. 26 nC/m² O b. 420 nC/m² O c. 33 nC/m² O d. 5.8 kC/m² O e.1 answer -
The following circuit has been connected for a long time, and the switch moves from position (a) to (b) at t=0. If the value of source C is 8V, calculate the capacitor voltage at t=0.08 .
El siguiente circuito lleva mucho tiempo conectado, y el interruptor se mueve de la posición (a) a (b) en t=0. Si el valor de la fuente C es 8 V, calcule el voltaje del capacitor en t=0.08. 200 w t=01 answer -
Calculate the value of the resistor so that the maximum power is transferred, and the value of this power, if the value of the voltage source is 10.4 volts. write in the solution in value of the power
Calcule el valor de la resistencia para que se se transfiera la máxima potencia, y el valor de esta potencia, si el valor de la fuente de voltaje es 10.4 volts. (Escriba en la solución en valor de l1 answer