Mechanical Engineering Archive: Questions from September 21, 2023
-
podría ayudarme con esta pregunta de procesos termodinámicos
5. En un diagrama \( T-s \) ¿el estado real de salida de una turbina adiabática tiene que estar del lado derecho del estado isoentrópico de salida? Explique1 answer -
podría ayudarme con esta pregunta de procesos termodinámicos
2. Un bloque de cobre de \( 60 \mathrm{~kg} \) inicialmente a \( 110^{\circ} \mathrm{C} \) se introduce dentro de un tanque aislado que contiene \( 150 \mathrm{~L} \) de agua a \( 25^{\circ} \mathrm{C1 answer -
podría ayudarme con esta pregunta de procesos termodinámicos
este proceso 3. Se comprime nitrógeno en un compresor adiabático desde \( 15^{\circ} \mathrm{C} \) y \( 100 \mathrm{kPa} \) hasta 200 "C y \( 400 \mathrm{kPa} \). Considere calores específicos vari1 answer -
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
0 answers
-
1 answer
-
0 answers
-
1 answer
-
0 answers
-
1 answer
-
A mass weighing 64 pounds lengthens a spring by 0.32 feet. At the beginning, the mass is released from a point that is 8 inches above the equilibrium position with a descending speed of 5 ft/s. a) Fin
2-. (40 puntos). Una masa que pesa 64 libras alarga 0.32 pies un resorte. \( \mathrm{Al} \) inicio la masa se libera desde un punto que está 8 pulgadas arriba de la posición de equilibrio con una ve0 answers -
0 answers
-
What point represents the depth of the center of pressure? Considering H = 1.0 m.
¿Que punto representa la profundidad del centro de presiones? Considerando \( \mathrm{H}=1.0 \mathrm{~m} \). * (10 puntos) \[ \begin{array}{l} A=1.0 \mathrm{~m} \\ B=1.05 \mathrm{~m} \\ C=0.83 \mathr1 answer -
1 answer
-
PROBLEM: The element shown in the figure has a rectangular cross section. Determine the factor of safety through the maximum shear and Von Mises theories at point C (35%) and at point D (35%). Conside
PROBLEMA: El elemento mostrado en la figura tiene una sección transversal rectangular. Determine el factor de seguridad por medio de las teorias de cortante máximo y Von Mises el punto C \( (35 \%)1 answer -
El eslabón para avión está hecho de una varilla de acero A992. Determine el menor diámetro de la varilla, con una precisión de \( \frac{1}{16} \) in, que puede soportar la carga de 4 kip sin pand1 answer -
La columna de acero A992 puede considerarse articulada en sus partes superior e inferior y reforzada contra su eje débil a la mitad de su altura. Determine la fuerza permisible máxima \( \mathbf{P}1 answer -
Se puede suponer que la columna de patín ancho W8 X 67, fabricada en acero, está fija en su base y articulada en su parte superior. Determine la mayor fuerza axial \( \mathbf{P} \) que puede aplicar1 answer -
La columna de madera está fija en su base y libre en su parte superior. Determine la carga \( P \) que puede aplicarse al borde de la columna sin ocasionar que ésta falle por pandeo o cedencia. \( E1 answer -
El tubo está hecho de cobre, tiene un diámetro exterior de \( 35 \mathrm{~mm} \) y un espesor de pared de \( 7 \mathrm{~mm} \). Determine la carga excéntrica \( P \) que puede soportar sin falla. E0 answers -
La columna estructural W14 \( \times 53 \) está fija en su base y libre en su parte superior. Determine la máxima carga excéntrica \( P \) que puede soportar sin que se presente pandeo o cedencia.1 answer -
3.17 Determine si el refrigerante \( R-22 \) en cada uno de los estados siguientes es un líquido comprimido, un vapor sobrecalentado o una mezcla de líquido saturado y vapor. a) \( 50^{\circ} \mathr1 answer