Mechanical Engineering Archive: Questions from October 22, 2023
-
1 answer
-
- A manufacturer plans to produce 200 pieces of wood that have the shape shown in the figure. These pieces have to be machined on a conventional lathe, starting from cylindrical logs 1 m in diameter a
\( \mathrm{Pb} .4 \) - Un fabricante planea producir 200 piezas de madera que tienen la forma mostrada en la figura. Dichas piezas tienen que mecanizarse en un torno convencional, partiendo de troncos2 answers -
13.- Una hoja de hierro de \( 0.01 \mathrm{~cm} \) de espesor separa una cámara de reacción en dos secciones. Un gas que contiene \( 5 \times 10^{20} \) átomos de \( \mathrm{H} / \mathrm{cm}^{3} \)1 answer -
During the carburization of a steel with 0.10% C, 1.2% C is introduced through the surface. When the iron is fcc, the carbon content is 0.90% at 0.016 cm below the surface after 1 hour. Calculate carb
13.- Durante la carburización de un acero con \( 0.10 \% \) de \( \mathrm{C} \), se introduce por la superficie \( 1.2 \% \) C Cuando el hierro es fcc, el contenido de carbono es \( 0.90 \% \) a \( 01 answer -
La celosía de la figura (dimensiones en \( \mathrm{m} \) ) esta realiza con barras de acero \( \mathrm{S} 275\left(\mathrm{E}=210 \mathrm{GPa}, \alpha=1.2 \cdot 10^{-5} \mathrm{C}^{-1}\right) \). Det0 answers -
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
CAUSE-EFEECT Rekationships (1) \( \quad Q=e_{r}-e_{c} \) (2) \( \quad i_{a}=\frac{K_{1} e_{v}-e_{b}}{s L_{a}+R_{a}} \) (3) \( \quad T=K_{2} \) ia (4) \( e_{b}=K_{3} s \theta \) (5) \( c=\frac{d_{1}}{d0 answers -
Pregunta \# 1 El carro \( D \) incrementa su velocidad en \( 1.5 \mathrm{~m} / \mathrm{s}^{\wedge} 2 \), mientras \( C \) mantiene la velocidad constante a \( 50 \mathrm{~m} / \mathrm{s} \). Determine1 answer -
Pregunta \# 2 Se muestra una pista de la montaña rusa donde la parte de la vía entre \( A \) y \( B \) es recta y horizontal, mientras que las porciones a la izquierda de \( A \) y a la derecha de \1 answer -
1 answer
-
Si el material es acero de máquina con un límite elástico de \( \sigma_{Y}=750 \mathrm{MPa} \), determine el factor de seguridad con respecto al rendimiento utilizando la teoría de la energía de1 answer -
1 answer
-
1 answer
-
1 answer
-
mostrar sistema de referencia para poder entender mejor. por favor
Lea cuidadosamente Cada enunciado y conteste en forma ordenada y correcta. Hacer paso a paso cada ejercicio. 4.10.-Una pelota golpea el suelo en \( A \) con una velocidad \( \mathbf{v}_{0} \) de \( 161 answer -
mostrar sistema de referencia para poder entender mejor. por favor
4.12.- Un disco A tiene una masa de \( 2 \mathrm{~kg} \) y se desliza sobre la superficie lisa con velocidad de \( 5 \mathrm{~m} / \mathrm{s} \) cuando choca con el disco B de \( 4 \mathrm{~kg} \), qu1 answer -
ejercicio de mecanica de fluidos
1. Aire es extraído de un gran tanque en el cual la temperatura y presión son \( 70{ }^{\circ} \mathrm{C} \) y \( 101 \mathrm{kPa} \) abs, respectivamente, a través de un conducto. A cierta ubicaci1 answer -
ejercicio de mecanica de fluidos
2. Fluye \( \mathrm{CO}_{2} \) a través de un dispositivo de tal manera que la presión de estancamiento es de \( 0.6 \mathrm{MPa} \) abs, la temperatura de estancamiento es de \( 400^{\circ} \mathrm1 answer -
ejercicio de mecanica de fluidos
3. Un flujo isotérmico de un gas \( \mathrm{CO}_{2} \) a 50 psi y \( 60^{\circ} \mathrm{F} \) sale de un tanque a través de un conducto con una sección transversal de salida de \( 0.5 \mathrm{ft}^{1 answer -
ejercicio de mecanica de fluidos
4. En una sección de un conducto la presión es de \( 30 \mathrm{psia} \), la temperatura \( 90^{\circ} \mathrm{F} \), la velocidad \( 575 \mathrm{ft} / \mathrm{s} \) y el área es de \( 0.3 \mathrm{1 answer -
ejercicio de mecanica de fluidos
5. Fluye aire fuera de un tanque donde la presión y temperatura son \( 150 \mathrm{psi} \) y \( 120^{\circ} \mathrm{F} \) respectivamente, el aire pasa a través de una tobera (1) hacia otro deposito1 answer -
3)Check the given transformation to remove a block from the feedback loop, transformation 4 of Table 6.1. 4) Simplify the block diagram of Figure 6.27 so that the block G(s) in the direct path is isol
3 Verificar la transformación dada para remover un bloque del lazo de realimentación, transformación 4 de la tabla 6.1. 4 Simplificar el diagrama de bloques de la figura 6.27 de nodu que el bloque1 answer -
1 answer