Mechanical Engineering Archive: Questions from October 14, 2023
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
Determine la distancia entre centros en milímetros, de la pieza y el agujero \[ \begin{array}{l} a=17 \mathrm{~mm} \\ b=1 \mathrm{~mm} \\ c=4 \mathrm{~mm} \end{array} \]2 answers -
Determine la distancia del eje \( x \) al centro del agujero en milímetros \[ \begin{array}{c} a=16 \mathrm{~mm} \\ b=2 \mathrm{~mm} \\ c=4 \mathrm{~mm} \end{array} \]1 answer -
1.- \( \mathrm{El} \) mecanismo de la figura tiene las siguientes dimensiones \( \mathrm{AB}=1.8 \) y \( \mathrm{AC}=1.44 \) pulgadas. El ángulo de \( \mathrm{AB} \) en la posición mostrada es de \(0 answers -
1 answer
-
Un tanque rígido (el volumen permanece constante) de \( 5 \mathrm{~m}^{3} \) contiene agua a \( 0.1 \mathrm{MPa} \) en fase de mezcla saturada líquido - vapor: \( 47.94 \mathrm{~kg} \) de líquido s1 answer -
Considere una turbina adiabática en estado estacionario con una entrada de vapor sobrecalentado a \( 5 \mathrm{MPa} \) y \( 600^{\circ} \mathrm{C} \), y un flujo de \( 20 \mathrm{~kg} / \mathrm{s} \)1 answer -
La cual se modifica (TG2) incluyendo un intercambiador de calor, un refrigerador y una cámara de recalentamiento, tal y como se muestra en la siguiente figura: a) Dibuje el ciclo termodinámico. (1 p0 answers -
5. El estado de deformación plana en un punto tiene las componentes \( \epsilon_{x}=-350\left(10^{-6}\right) \), \[ \epsilon_{y}=200\left(10^{-6}\right), \tau_{x y}=80\left(10^{-6}\right) \] a) Deter1 answer -
Shaft BD is connected to a spherical joint at point B, and bevel gear A is fixed at its other end. The gear is coupled with a fixed bevel gear C. The shaft of gear A rotates with angular velocity 𝜔
El eje BD está conectado a una unión esférica en él punto B, y el engranaje cónico A está fijo en su otro extremo. El engranaje se acopla con un engranaje cónico fijo \( \mathrm{C} \). El eje d0 answers -
Determine la componente de la reacción horizontal en el perno \( \mathrm{C} \) sobre el elemento \( B C D E \). Si \( a=3.0 \) in, \( b=8.0 \) in, \( c=3.0 \) in \( \vee P=80.0 \) Lb.1 answer -
6. La varilla \( A B \) está unida a los collarines en sus extremos, mediante rótulas. En el instante que muestra la figura el collarín A tiene una aceleración \( \mathbf{a}_{\mathbf{A}}=6 \mathbf1 answer -
The cutter shown is used to cut and trim printed circuit boards. For the position shown, determine the vertical component of the shear force exerted at E. Knowing that a = 46 mm, b = 9 mm, c = 89 mm,
La cortadora mostrada se usa para cortar y rebajar láminas de circuitos impresos. Para la posición mostrada, determine la componente vertical de la fuerza cortante ejercida en \( \mathrm{E} \). Si s1 answer -
Se aplica una fuerza \( F=16 \mathrm{lb} \) a las manijas de la tenaza. Determine la magnitud de la fuerza desarrollada sobre el vástago del perno \( A \) en las quijadas. Considere que \( a=5 \) in1 answer -
Determina la magnitud de la reacción en el punto \( \mathrm{A} \) del bastidor mostrado. Si una fuerza dirigida hacia abajo de \( 378 \mathrm{~N} \) se aplica en el punto B.1 answer