Mechanical Engineering Archive: Questions from October 05, 2023
-
The figure shows the upper part of a pulley arch subjected to three forces. Find the coordinates of a point P where the system composed of the three forces can be reduced to a single equivalent force.
Pb. 4. (1Pto.) En la figura se muestra la parte superior de un arco de poleas sometido a tres fuerzas. Hallar las coordenadas de un punto \( P \) donde el sistema compuesto por las tres fuerzas pueda1 answer -
If it is known that the disk has a constant angular velocity of 485 rad/s in a clockwise direction. Determine the speed of collar D when = 63°, the radius of the disk is R =3 and the length of the ba
Si se sabe que el disco tiene una velocidad angular constante de \( 485 \mathrm{rad} / \mathrm{s} \) en el sentido de las manecillas del reloj. Determine la velocidad del collarÃn \( \mathrm{D} \) cu1 answer -
Determine the internal force on the ED, EB and AB bars; and set whether it is tension or compression. Perform the exercise with the Right Section and then with the Left Section.
1. Determine la fuerza interna en las barras ED, EB y AB; y establezca si es de tensión o compresión. Realice el ejercicio con la Sección Derecha y posteriormente con la Sección Izquierda.1 answer -
0 answers
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
Usando el método de nodos calcule las fuerzas internas en libras de los siguientes elementos \( D E, C D, C E \) y \( \mathrm{BC} \), indique si el elemento se encuentra a tención o compresión. Par1 answer -
1 answer
-
2. A cantilever beam is attached laterally to a column with three (3) M12x1.75 ISO Class 5.8 screws (Sy = 420 MPa). The beam supports a transverse load of 12 kN as shown in the figure. Determine the s
2. Una viga en voladizo está agarrada lateralmente a una columna con tres (3) tornillos M12x1.75 ISO Class \( 5.8\left(\mathrm{~S}_{y}=420 \mathrm{MPa}\right) \). La viga soporta una carga transversa1 answer -
La viga mostrada soporta una fuerza distribuida f=48kN//m. La longitud L=9.9m. Determine la magnitud del momento interno en x=7.66m. Input units: kNm
La viga mostrada soporta una fuerza distribuida \( \mathrm{f}=48 \mathrm{kN} / \mathrm{m} \). La longitud \( L=9.9 \mathrm{~m} \). Determine la magnitud del momento interno en \( \mathrm{x}=7.66 \math1 answer -
For the loaded plate shown below, assume \( \sigma_{x x}=-p \mathrm{f}(x) \). Determine the function \( \mathrm{f}(x) \) using the Airy Stress function approach. \( \begin{array}{c}\varnothing=-\frac1 answer -
1. The figure shows a pressurized cylindrical tank with an internal diameter D = 4 in, thickness t = 0.375 in, length L = 12 in and with lids of thickness w = 0.75 in. The caps and cylinder are made o
La figura muestra un tanque cilÃndrico presurizado con un diámetro interno \( D= \) \( 4 \mathrm{in} \), grosor \( t=0.375 \mathrm{in} \), largo \( L=12 \mathrm{in} \) y con tapas de espesor \( w=0.0 answers -
2. A cantilever beam is attached laterally to a column with three (3) screws M12x1.75 ISO Class 5.8 (Sy = 420 MPa). 420 MPa). The beam supports a transverse load of 12 kN as shown in the figure. Deter
Una viga en voladizo está agarrada lateralmente a una columna con tres (3) tornillos \( M 12 x 1.75 \) ISO Class \( 5.8\left(S_{y}=420 \mathrm{MPa}\right) \). La viga soporta una carga transversal de0 answers -
please
2. Una viga en voladizo está agarrada lateralmente a una columna con tres (3) tornillos \( M 12 \times 1.75 \) ISO Class \( 5.8\left(\mathrm{~S}_{y}=420 \mathrm{MPa}\right) \). La viga soporta una ca1 answer -
a) \( \mathrm{Calcule} \mathrm{Fl}_{R}, \alpha, \beta, \gamma \) de \( F_{R} \) b) Calcula la Playucción de \( F_{R} \) en el je \( O C \) \( \left(F_{k}\right)_{a c} \) C) Calcula el momunto total e0 answers -
Para la armadura mostrada, Determine por el método de nodos la magnitud de la fuerza en el elemento AE \[ \begin{array}{c} F=24 N \\ P=19 N \\ a=2.7 \mathrm{~m} \\ b=1 \mathrm{~m} \\ \theta=72^{\circ1 answer -
0 answers
-
1 answer
-
1.56 El poste vertical está asegurado por tres cables. Los cables están pretensados de modo que la resultante de las fuerzas de los cables \( \mathbf{F}, \mathbf{Q} \) y \( \mathbf{P} \) está dirig1 answer -
Al usar el cortador de pernos que se muestra, un trabajador aplica dos fuerzas de \( 258 \mathrm{~N} \) a las manijas. Determine la magnitud de las fuerzas ejercidas por el cortador en el perno. Escri1 answer -
Determine the force on element ABC SHOWN IN THE FIGURE
3. Determine las fuerzas sobre el elemento \( A B C \) que se muestra en la figura.1 answer -
quiero saber los resultados de estos problemas
5.120. Cuña movil, Una cuña de masa \( M \) descansa en una mesa horizontal sin friccibn. Un bloque de masa m se coloca sobre la cuha (figura 5.84a). No hay fricción entre el blogue y la cuña. El1 answer -
Para la armadura mostrada, Determine por el método de nodos la magnitud de la fuerza en el elemento \( A E \) \[ \begin{array}{c} \mathrm{F}=61 \mathrm{~N} \\ \mathrm{P}=59 \mathrm{~N} \\ \mathrm{a}=1 answer