Mechanical Engineering Archive: Questions from October 04, 2023
-
0 answers
-
4. Consider the following system in State Space: a) Determine if it is controllable and observable. Try doing it by hand and then in Matlab b) Design a controller for the system using the desired pole
4. Considerar el siguiente sistema en Espacio de Estados: \[ \begin{array}{c} \dot{x}=\left[\begin{array}{ccc} -6 & -11 & -6 \\ 1 & 0 & 0 \\ 0 & 1 & 0 \end{array}\right]\left[\begin{array}{l} x_{1} \\1 answer -
1 answer
-
cómo puedo resolver este problema
En el boceto \( a \) se muestra una parte de una máquina textil. Las dimensiones se dan en milÃmetros. La potencia de entrada para el sistema es \( 5 \mathrm{~kW} \) en el eje \( \mathrm{S}_{1} \) y0 answers -
3. El caudal que ingresa en la T de cobre de 5/8 OD mostrada en la figura es 6,5 GPM. Calcule la Velocidad del lÃquido en ft/s para cada una de las salidas. v2=? v3=?
3. El caudal que ingresa en la T de cobre de \( 5 / 8 \) OD mostrada en la figura es \( 6,5 \mathrm{GPM} \). Calcule la Velocidad del lÃquido en \( \mathrm{ft} / \mathrm{s} \) para cada una de las sa1 answer -
2. Si la capsula de observación submarina de 6.500 kg de masa mostrada en la figura, tiene capacidad para siete tripulantes con masa promedio de 85 kg. Determine la Fuerza en Newtons para mantener la
2. Si la capsula de observación submarina de \( 6.500 \mathrm{~kg} \) de masa mostrada en la figura, tiene capacidad para siete tripulantes con masa promedio de \( 85 \mathrm{~kg} \). Determine la Fu1 answer -
. Una máquina de forjado tiene una capacidad máxima de aplicación de fuerza de 600 kN y se desea trabajar la pieza cilÃndrica obtenida del ejercicio anterior. La curva de fluencia del material est
Una máquina de forjado tiene una capacidad máxima de aplicación de fuerza de \( 600 \mathrm{kN} \) y se desea trabajar la pieza cilÃndrica obtenida del ejercicio anterior. La curva de fluencia del0 answers -
0 answers
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
Problem 3 (25pts.): A beam is supported on the far right by a pin and by a cable (AB) on the far left. If a force Fa is applied at point C, determine the internal forces (normal, shear and moment) at
Problema 3 (25pts.): Una viga es apoyada en el extremo derecho por un pin y por un cable (AB) en el extremo izquierdo. una fuerza \( F_{3} \) en el punto \( C \), determine las fuerzas internas (norma1 answer -
Indicate the coordinates of the centroid (x, T) of the cross-sectional area.
Indique las coordenadas del centroide \( (\bar{x}, \bar{y}) \) del área de la sección transversal.1 answer -
Indicate the coordinates of the centroid (x, y) of the cross section area
Indique las coordenadas del centroide \( (\bar{x}, \bar{y}) \) del área de la sección transversal.1 answer -
4. Los centros de gravedad del fuselaje de un avión \( A \) y de sus alas \( B \) y \( C \), se encuentran en la posición que se muestra en la Figura debido a una distribución desigual del combusti1 answer -
0 answers
-
1 answer
-
1 answer
-
DESCRIPCIÓN DEL PROBLEMA Uno de los mecanismos más comunes en ingenierÃa es el Biela-Manibela-Corredera. Para el ejercicio mostrado, resuelva lo siguiente, considerando que la velocidad angular \(0 answers -
Determine the internal force on the ED, EB and AB bars; and set whether it is tension or compression. Perform the exercise with the Right Section and then with the Left Section.
1. Determine la fuerza interna en las barras ED, EB y AB; y establezca si es de tensión o compresión. Realice el ejercicio con la Sección Derecha y posteriormente con la Sección Izquierda.1 answer -
Determine the strength in the EF and GI elements of the armor shown in the figure.
2. Determine la fuerza en los elementos EF y GI de la armadura mostrada en la figura.2 answers -
La compañÃa de grúas y polipastos Grumex, tiene en la fase de prototipado la grúa portable que se muestra. Sus clientes principales se consideran los talleres mecánicos, por ello se han planteado1 answer