Mechanical Engineering Archive: Questions from November 27, 2023
-
1 answer
-
respuesta 1016 Cº
4-25 Los amortiguadores de los sistemas de suspensión automotrices están fabricados con varillas de acero calentadas y enrollados en bobinas mientras están en estado dúctil. Se tienen varillas de1 answer -
Se desea modelar la din´amica de control de un veh´ıculo de reparto, el cual se representa mediante una barra r´ıgida (modela el chasis), con masa m y momento de inercia Ic con respecto al centro
Figura 2: Modelo de la mitad de un camión de reparto. 1. Ecuación (es) diferencial (es) de la Dinámica del Sistema. 2. Considerando como estados del sistema \( x_{1}=x, x_{2}=\theta, x_{3}=\dot{x},1 answer -
El objetivo del sistemas de control de un helic´optero mostrado en la figura 1, es controlar el ´angulo de cabeceo (θ(t)) ajustando el ´angulo de empuje del rotor (δ(t)). Las ecuaciones de movimi
\[ \begin{array}{c} \ddot{\theta}(t)=-\sigma_{1} \dot{\theta}(t)-\alpha_{1} \dot{x}(t)+n \delta(t) \\ \ddot{x}(t)=g \theta(t)-\alpha_{2} \dot{\theta}(t)-\sigma_{2} \dot{x}(t)+g \delta(t) \end{array} \0 answers -
0 answers
-
0 answers
-
0 answers
-
0 answers
-
send answer please?
[1].- (0,5 Pts). Calcular los valores de tensión alterna y media de flexión, en la sección situada \( 10 \mathrm{~mm} \) a la derecha del rodamiento derecho. Se trata del eje de entrada de un reduc1 answer -
Problema 1. (40 puntos) La viga mostrada soporta las cargas mostradas. a) Dibuje el diagrama de cargas (4) b) Dibuje el diagrama de cortantes (7) c) Dibuje el diagrama de momentos (9) d) Determine el1 answer -
Problema 2. Para la siguiente viga de longitud \( 10 \mathrm{ft} \), considere \( P_{1}=20 \) kips, \( P_{2}=15 \) kips y \( P_{3}=10 \) kips. a) Dibuje el diagrama de cargas (5) b) Dibuje el diagrama1 answer -
Problema 3 (15 puntos) Para el siguiente caso obtenga el valor de: a) El momento actuando a 26 in a partir del apoyo A (5) b) El momento máximo actuando en la viga (indique la posición exacta a part1 answer -
Problema 4 (10 puntos) Una viga tiene la sección transversal mostrada, para dicha sección a) Obtenga el centroide (4) b) Obtenga el momento de inercia respecto al eje \( X \) (6) c) Obtenga el momen1 answer -
1 answer
-
1. A la varilla de aluminio \( A D \) se le ajusta una coraza que se emplea para aplicar una presión hidrostática de 8000 psi a la porción \( \mathrm{BC} \) de 12 pulg de la varilla. Si se sabe que1 answer -
2. Determine la dilatación e y el cambio de volumen \( \Delta V \) del tramo de \( 200 \mathrm{~mm} \) de la varilla mostrada en la figura 2, si (a) la varilla es de acero con \( E=250 G P a \) y \(1 answer -
3. (a) Para la carga axial mostrada en la figura 3, determine el cambio en altura y el cambio en volumen del cilindro de latón mostrado. (b) Resuelva el inciso a, suponiendo que la carga es hidrostá1 answer -
4. Un cubo de \( 70 \mathrm{~mm} \), elaborado con epóxico reforzado con fibras de grafito con las fibras alineadas en la dirección y, se sujeta a una carga compresiva de \( 180 \mathrm{kN} \) en la1 answer -
5. Una esfera sólida de acero de 8 pulg de diámetro se introduce en el océano donde la presión es de \( 7.1 \mathrm{ksi} \) (alrededor de 3 millas bajo la superficie). Sabiendo que \( E=31 \times1 answer -
1 answer
-
0 answers
-
otros elementos como se muestra en la figura. Hallar: \( \mathbb{Z} \) La matriz de rigidez global.La matriz de rigidez reducida.Las deformaciones.Las reacciones. \( 囚 \) Los esfuerzos.Analizar una0 answers -
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer