Mechanical Engineering Archive: Questions from November 23, 2023
-
1 answer
-
1 answer
-
ejercicio de mecánica de fluidos
1. Se tiene el flujo de agua en una sección de área variable que tiene \( 30 \mathrm{~cm} \) de diámetro en la sección 1 y en la sección 2 tiene \( 15 \mathrm{~cm} \) de diámetro, el caudal es d1 answer -
ejercicio de mecánica de fluidos
2. El agitador mostrado en la figura revuelve una sustancia con \( \rho=1200 \frac{\mathrm{kg}}{\mathrm{m}^{3}} \) y gira a una velocidad \( \Omega=10 \mathrm{rpm} \), el coeficiente de arrastre en la1 answer -
1 answer
-
0 answers
-
0 answers
-
1. Dos chapas de acero de 12 mm de espesor con una unión por solapo de una sola fila de remaches. El paso de remachado es de 6.50 cm y el diámetro de los remaches 19 mm. La carga que soporta una lon
1. Dos chapas de acero de \( 12 \mathrm{~mm} \) de espesor con una unión por solapo de una sola fila de remaches. El paso de remachado es de \( 6.50 \mathrm{~cm} \) y el diámetro de los remaches 191 answer -
1 answer
-
1 answer
-
1 answer
-
El primer nodo es ABC realizar previamente la sumatoria de fuerzas y de momentos. Sacar la fuerza de las secciones LF y HI.
Determinar la sumatoria de fuerzas, sumatoria de momentos, primer nodo, indicar porque es el nodo de arranque y al menos 2 secciones.0 answers -
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1. There is a crane that holds a .5kg weight, it remains static when it is at 90°. The crane is held with a rope that goes from the arm to an embedment. Calculate the tension of the string and all th
Se tiene una grúa que sostiene una pesa de \( .5 \mathrm{~kg} \), esta se mantiene estática cuando está a \( 90^{\circ} \). Se sostiene con una cuerda que va desde el brazo hasta un empotramiento.0 answers -
1 answer
-
1 answer
-
1 answer
-
Método de Newton (Diagrama de Cuerpo Libre) PT1. Un sistema de palanca y eslabones conectados po pasadores, se utiliza como un mecanismo de palanca en un prensa; según se muestra en la figura. Deter1 answer -
PT5. En la figura se muestra una bomba manual de alta presión que se emplea para elevar la presión del aceite en un circuito hidráulico. Cuando la palanca está en equilibrio estático, con \( \the0 answers -
PT6. La unidad de bombeo se usa para extraer petróleo, cuando la viga del balancÃn \( \mathrm{ABC} \) está en posición horizontal, la fuerza que actúa en el cable de perforación situado en la ca1 answer -
PT2. Para el mecanismo mostrado en la figura, de una prensa mecánica articulada de 6 eslabones, determine el par de torsión \( \boldsymbol{T}_{\boldsymbol{A}} \) necesario en la manivela \( \mathrm{0 answers -
PT3. Para el mecanismo mostrado en la figura, determine el par de torsión \( \boldsymbol{T}_{\boldsymbol{A}} \) necesario en la manivela AB, para mantener el equilibrio estático de una fuerza de tra1 answer -
PT4. Para el mecanismo mostrado en la figura, de una prensa mecánica articulada de 6 eslabones, determine el par de torsión \( T_{A} \) necesario en la manivela \( \mathrm{AB} \) (eslabón 2), para0 answers -
1 answer
-
0 answers
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
12.D6 iEs posible producir un acero 4340 templado en aceite y revenido con un limite elástico minimo de \( 1500 \mathrm{MPa} \) y una ductilidad minima de \( 42 \% \mathrm{Z} \) ? En caso afirmativo,1 answer