Mechanical Engineering Archive: Questions from December 06, 2023
-
1 answer
-
0 answers
-
1 answer
-
The stress values given belong to the stress state of the element which is rotated 30° counterclockwise. Find: a) σx , σy and ζxy when the element is in initial position. b) σn max and σn min an
Problema \( \mathbf{N}^{0} \) 32: Los valores de los esfuerzos indicados pertenecen al estado de esfuerzo del elemento que se encuentra girado \( 30^{\circ} \) en el sentido contrario a las manecillas1 answer -
A trapezoidal shaped plate of thickness t= 0.50 cm, with base greater than 3a and base less than 2a, is fixed at its ends and length 3L. Note: Work literally first and then replace. Calculate:a) The m
Problema \( \mathrm{N}^{0} 33 \) Un placa de forma trapezoidal de espesor \( \mathrm{t}=0.50 \mathrm{~cm} \), con base mayor de 3a y base menor de \( 2 \mathrm{a} \), se encuentra fija en sus extremos1 answer -
Two bars are at room temperature of 50º F as shown in the figure. Bar AB of square section of side 3 in. and bar BC of diameter 2.50 in. Determine: a)The temperature required for point C to touch the
Problema \( \mathrm{N}^{0} 34 \) : Dos barras están a temperatura ambiente de \( 50^{\circ} \mathrm{F} \) como se muestran en la figura. La barra \( \mathrm{AB} \) de sección cuadrada de lado 3 pulg1 answer -
La barra \( A B \) del mecanismo de cuatro barras.s mostrado en la figura, tiene una velocidad angular constante de \( 5 \mathrm{rad} / \mathrm{s} \) en sentido horario. Determine: las aceleraciones a1 answer -
1 answer
-
1 answer
-
0 answers
-
1 answer
-
0 answers
-
1 answer
-
Pb.2. (1Pto.) El tensor \( B E \) de la estructura mostrada en la figura es de filete simple cuadrado, de \( 12 \mathrm{~mm} \) de diámetro medio y avanza \( 1 \mathrm{~mm} \) por cada vuelta complet0 answers -
Solve using laplace
1. \( y^{\prime \prime}-1 y^{\prime}+9 y=5 t, \quad y(0)=2 \quad y^{\prime}(0)=-1 \) 2. \( y^{\prime \prime}+4 y^{\prime}=\cos (t-3)+4 t, \quad y(3)=0 \quad y^{\prime}(3)=7 \)1 answer -
6. Compute the double Fourier sine series for f(x, y) on the rectangle 0 ≤ x ≤ π, 0 ≤ y ≤ π a) f(x, y)=1 b) f(x, y) = {0, if x<y 1, if x ≥ y c) f(x, y) = xy
6. Compute the double Fourier sine series for \( f(x, y) \) on the rectangle \( 0 \leq \) \( x \leq \pi, 0 \leq y \leq \pi \) a) \( f(x, y)=1 \) b) \( f(x, y)=\left\{\begin{array}{l}0, \text { if } x1 answer -
0 answers
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
0 answers
-
1 answer
-
P11. Determine si el dron se voltea o se desliza. El dron tiene un peso de \( 100 \mathrm{lb} \). La persona esta aplicando una fuerza igual a \( 200 \mathrm{lb} \). El coeficiente de fricción estát1 answer -
La bomba de la figura envia agua del almacenamiento inferior al superior a razón de 2 pies \( { }^{3 / 5} \). La pérdida de energía entre la tuberia de succión y la entrada de la bomba es de 6 pie1 answer -
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
The bar has a diameter of 100 mm. Determine the stress components that act at point B, find the principal stresses at the point and using the static failure theories applicable to brittle materials, c
La barra tiene un diámetro de \( 100 \mathrm{~mm} \). Determine las componentes del esfuerzo que actúan en el punto \( B \), encuentre los esfuerzos principales en el punto y empleando las teorías1 answer -
The figure illustrates the free body diagram of a part of a connecting link, with stress concentrators in three sections. The dimensions are r=0.10 in, d=0.50 in, h=0.40 in, W1=4.50 in and W2=4.0 in.
En la figura se ilustra el diagrama de cuerpo libre de una parte de un eslabón de conexión, con concentradores de esfuerzos en tres secciones. Las dimensiones son \( r=0.10 \) pulg, \( d=0.50 \) pul1 answer -
The shaft shown in the figure is made of cold-drawn AISI 1018 steel. The shaft rotates at 1800 rpm and rests on bearings A and B. The force applied is 2500 lbf. Determine the minimum safety factor aga
El eje que se muestra en la figura está fabricado con acero AISI 1018 estirado en frío. EI eje gira a \( 1800 \mathrm{rpm} \) y se apoya en los cojinetes \( A \) y \( B \). La fuerza aplicada es de0 answers -
1 answer
-
1 answer