Mechanical Engineering Archive: Questions from September 29, 2022
-
English: The support shown below is connected to a control cable at point B and has a hinge at C. For the loads shown, determine the direction, in degrees, of the reaction at the support at point C wh
El soporte que se muestra a continuación, está conectado a un cable de control en el punto B y tiene una articulación en C. Para las cargas mostradas, determine la dirección en grados, de la reacc2 answers -
A un automóvil se le pone un volante deportivo \( (B) \) que es más pequeño que un volante convencional (A). ¿Cuál de las siguientes afirmaciones es la correcta? Se requiere mayor fuerza para gir2 answers -
Para la viga mostrada, determine cuáles de las reacciones son diferentes de cero. Ay y MA Sólo MA Ax, Ay y MA Axy Ay Ax y MA Sólo Ay Solo Ax2 answers -
La Barra AB, tiene un pasador en A y esta sobre una pared lisa en \( B \). Selecciona el diagrama de cuerpo libre, que mejor representa las reacciones.2 answers -
Asumiendo las reacciones en el apoyo como positivas, plantee las sumatoria de fuerzas en " \( y \) " positivas hacia arriba. Para cada carga, anteceda el signo (+, - o N/A) según corresponda. \( P \)2 answers -
Asumiendo las reacciones en el apoyo como positivas, plantee las sumatoria de momentos en el punto \( \mathrm{K} \) positivos en contra de las manecillas del reloj. Para cada carga, anteceda el signo2 answers -
On the options take the ft as 40 not 30
Seleccione el Diagrama de Cuerpo Libre de la siguiente figura d)2 answers -
Determina la fuerza en el elemento CD para los datos que a continuación se muestran: \[ a=2.6 \mathrm{~m} \quad b=3.5 \mathrm{~m} \quad \mathrm{~F} 1=653 \mathrm{~N} \quad \mathrm{~F} 2=177 \mathrm{~2 answers -
Determina la fuerza en el elemento CF para los datos que a continuación se muestran: \[ a=7.6 \mathrm{~m} \quad b=3.3 \mathrm{~m} \quad \mathrm{c}=4.1 \mathrm{~m} \quad \mathrm{~d}=5.5 \mathrm{~m} \q0 answers -
Determina la fuerza en el elemento \( \mathrm{CJ} \) para los datos que a continuación se muestran: \[ a=3.9 \mathrm{~m} \quad b=9.1 \mathrm{~m} \quad \mathrm{~F} 1=390 \mathrm{~N} \quad \mathrm{~F}2 answers -
The support shown below is connected to a control cable at point B and has a hinge at C. For the loads shown, determine the magnitude of the reaction at the support at point C when: d1 = 0.17 meters d
El soporte que se muestra a continuación, está conectado a un cable de control en el punto B y tiene una articulación en C. Para las cargas mostradas, determine la magnitud de la reacción en el ap2 answers -
Assuming the reactions at the support as positive, I planted the sum of moments with respect to point A, positive counterclockwise. For each load, precede the sign (+,- or N/A) as appropriate. Precede
Asumiendo las reacciones en el apoyo como positivas, planté la sumatoria de momentos con respecto al punto A, positivos en contra de las manecillas del reloj. Para cada carga, anteceda el signo (+,-2 answers -
El @ es cada sección de la base mide 3 m (C,E,G,I,K)
Para la armadura que se muestra, determine la fuerza interna u axial que experimenta el elemento JL, si el elemento está en compresión agregue el signo menos. De su respuesta en \( \mathrm{kN} \) co2 answers -
0. Cuál es el objetivo al hacer rotar el "chuck" manualmente antes de comenzar una operación de corte? (2 pts.) 11. Cuál es la diferencia entre realizar una operación de corte manual y una operaci2 answers