Mechanical Engineering Archive: Questions from November 28, 2022
-
1. The figure below is a still image of you making initial heel contact while walking. At that moment, a ground reaction force is verified in the knee aligned with the axis of the femur (FL) longitudi
1. La siguiente figura es ura still image de usted haciendo un cootacto ieicial de talón mientras camira. En ese momento en la rodilla se verifica una fuena de reacciba del suelo alineada con el eje2 answers -
2 answers
-
1. The spring shown \( \left(k=20 \mathrm{~N} / \mathrm{m}^{2}\right) \) is unstretched when \( \mathrm{s}=0 \). The \( 5-\mathrm{kg} \) cart moves to position \( \mathrm{s}=-1 \mathrm{~m} \) and is r2 answers -
2. Un escalador en roca de peso \( W \) está unido, por seguridad, a una cuerda amarrada a una distancia \( \mathrm{h} \) debajo de él. Supongá que el alpinista cae y que la cuerda se comporta como2 answers -
3. La caja de \( 10 \mathrm{~kg} \) que se muestra en la figura parte desde el reposo sobre la superficie lisa y se somete a la fuerza horizontal descrita en la gráfica. Los coeficientes de fricción2 answers -
4. Las dos bolas mostradas, cada una con peso de \( 1 \mathrm{lb} \), cuelgan de cuerdas con longitud \( \mathrm{L}=3 \) pies. La bola izquierda se suelta desde el reposo con \( \theta=35^{\circ} \).2 answers -
Determinar por el método de su preferencia las fuerzas a las que trabajan los miembros EG, GF. FH y EF de la siguiente armadura. (5 puntos)2 answers -
Determinar por el método de tu preferencia las fuerzas a las que trabajan los miembros ML, OE, DE, JH y JG de la siguiente armadura. (6 puntos)2 answers -
2. A 0.5kg indoor soccer ball is kicked towards the goalie in an offensive situation. The goalkeeper stops it with the inner part of the knee just at the level of the tibial plateau, with the knee ext
2. Una pelota de soccer de saldn de 0.5Kg es pateada hacia el portero en una situacidn ataque. [I portero la detiene con la parte interna de la rodilla justo a la altura de la meseta thbul, con la rod2 answers -
Given \( a=49 \mathrm{~m} \). and \( b=\frac{1}{1} \). determine the shaded area's centroid \( y \) \[ \bar{y}=\quad m \]2 answers -
Suction=1.15baf, discharge=6.75, isentropic efficiency=67.5%, freon fluid 22 Calculate by the graphical method A) compression power B) gas discharge temperature
14. Cálculo por el método gráfico (GPA). Compresión de gas "PROPANO" Cálculo de la Temperatura de descarga Diagrama P - H Fluido puro Pasos a seguir: 1. Se marca en el eje de las ordenadas del di0 answers -
resolver, con Te=25.84
7-69 En una instalación industrial se va a precalentar el aire para la combustión antes de meterlo en un horno, por medio de agua caliente a \( 90^{\circ} \mathrm{C} \) que fluye por los tubos de un0 answers -
3–197 A flat wall with a surface temperature of 300C is attached to straight triangular aluminum fins (k = 236 W/mK). Fins are exposed to ambient air of 25C and the coefficient of heat transfer by c
3-197 Una pared plana con una temperatura superficial de \( 300^{\circ} \mathrm{C} \) está unida a aletas triangulares de aluminio rectas \( (k=236 \mathrm{~W} / \mathrm{m} \cdot \mathrm{K}) \). Las2 answers -
Given \( a=35 \mathrm{~m} \), and \( b=\frac{1}{35} \), determine the shaded area's centroid \( \bar{y} \)2 answers -
2 answers
-
5. This symbol specifies a weld of: a. Full penetration. b. Partial penetration. c. Fillet on both sides. d. Steak on one side only. 4. This weld symbol asks for a depth of joint preparation 8(12)\/
5. Este simbolo especifica una soldadura de: a. Penetración completa. b. Penetración parcial. c. Filete en ambos lados. d. Filete en un solo lado. 4. Este simbolo de soldadura pide una profundidad2 answers -
2. In Figure 1, Angle B is called: a. Weld angle. b. Angle of the joint. c. Bisel Angle. d. None of A, B, C. 1. In this figure the arrow points to a welding defect known as: a. undermined. b. Wel
2. En la Figura 1, el Angulo B se denomina: a. Ángulo de la soldadura. b. Angulo de la unión. c. Ángulo del Bisel. d. Ninguna de A, B, C. 1. En esta figura la flecha señala un defecto de soldadur2 answers -
Given \( a=59 \mathrm{~m} \) and \( b=\frac{1}{59^{\prime}} \) determine the shaded area's centroid \( \bar{y} \) [2 marks]2 answers