Mechanical Engineering Archive: Questions from May 24, 2022
-
a) The bar is homogeneous, determine the moment (N-m without decimals) about pin O if wire A is cut and the bar is allowed to rotate. (5%) b) Calculate the angular acceleration of the rod (rad/s2 to
wwwwwwwwwwww 1,000 N 0.40 m Bar mass 540 Kg B A 2,00 m T (a) La barra es homogénea, determine el momento (N-m sin decimales) con respecto al pin O si se corta el cable A y la barra puede rotar. (5%)1 answer -
The block moves as shown when the load is applied to it: (a) Determine the horizontal speed (m/s to 2 decimal places) after 8 seconds. (twenty%) (b) Determine the required time (seconds to 2 decimal
points Save Am Block mass 180 Kg 42° 12 m/s μk = 0.44 El bloque se mueve como se muestra cuando se le aplica la carga: (a) Determine la velocidad horizontal (m/s con 2 decimales) luego de 8 segundos1 answer -
Please help fast!!: translation: The block moves as shown when the load is applied to it: (a) Determine the horizontal speed (m/s to 2 decimal places) after 8 seconds. (twenty%) (b) Determine the re
1,600 N Block mass= 180 Kg 42° 12 m/s uk= 0.44 El bloque se mueve como se muestra cuando se le aplica la carga: (a) Determine la velocidad horizontal (m/s con 2 decimales) luego de 8 segundos. (20%)1 answer -
a) The bar is homogeneous, determine the moment (N-m without decimals) about pin O if wire A is cut and the bar is allowed to rotate. (5%) b) Calculate the angular acceleration of the rod (rad/s2 to
1,000 N 0.40 m 4 Bar mass=540 Kg B 2.00 m ㅏ (a) La barra es homogénea, determine el momento (N-m sin decimales) con respecto al pin O si se corta el cable A y la barra puede rotar. (5%) (b) Calcule1 answer -
The block moves as shown when the load is applied to it: (a) Determine the horizontal speed (m s to 2 decimal places) after 8 seconds. (twenty%) (b) Determine the required time (seconds to 2 decimal p
1,600 N Block mass 180 Kg 42" 12 m/s uk = 0.44 El bloque se mueve como se muestra cuando se le aplica la carga (a) Determine la velocidad horizontal (m/s con 2 decimales) luego de 8 segundos (20%) (b)1 answer -
*Please I need a development by steps and explained how it was done. Especially how to get the factor of safety, it is the part that most complicates me* An AISI 1020 cold-rolled steel pressurized cy
25 -850- 600 30 25 30 Tabla E-9 Propiedades mecánicas de algunos aceros al carbono Datos de varias fuentes. Valores aproximados. Consulte a los fabricantes de material para mayor información Númer1 answer -
The block moves as shown when the load is applied to it: a) Determine the horizontal velocity (m/s to 2 decimal places) after 6 seconds. (20%) b) Determine the time required (seconds to two decimal p
1,500 N Block mass = 160 Kg 40° 10 m/s μk = 0.40 El bloque se mueve como se muestra cuando se le aplica la carga: (a) Determine la velocidad horizontal (m/s con 2 decimales) luego de 6 segundos. (201 answer -
The block moves as shown when the load is applied to it: a) Determine the horizontal velocity (m/s to 2 decimal places) after 6 seconds. (20%) b) Determine the time required (seconds to two decimal p
1,500 N Block mass= 160 Kg 40° 10 m/s uk = 0.40 El bloque se mueve como se muestra cuando se le aplica la carga: (a) Determine la velocidad horizontal (m/s con 2 decimales) luego de 6 segundos. (20%)1 answer -
HELP ASAP: An object with a mass of 12 kg moves in a straight line path at a speed of 15 m/s, the object is subjected to a force of 20 N in the same direction of movement, this force is uniformly red
Un objeto con una masa de 12 Kg se mueve en una trayectoria rectlinea a una velocidad de 15 m/s, el objeto está sujeto a una fuerza de 20 N en el mismo sentido del movimiento, esta es fuerza es reduc1 answer -
1 answer
-
An object with a mass of 10 kg moves in a straight line at a speed of 9 m/s, the object is subjected to a force of 24 N in the same direction of movement, this force is uniformly reduced to 12 N in a
Un objeto con una masa de 10 Kg se mueve en una trayectoria rectlínea a una velocidad de 9 m/s, el objeto está sujeto a una fuerza de 24 N en el mismo sentido del movimiento, esta es fuerza es reduc1 answer -
1 answer
-
Determine the location of the coordanates of the centroid of the area shown( xc and yc with two decimal places). Prepare a Free Body Diagram and a table with the calculations withe detail.
35 points 5 15 cm 5 cm 14 3 cm 6 cm 12 cm 12 cm 9 cm Determine la ubicación de las coordenadas del centroide de área mostrada (xe & ye con dos lugares decimales), prepare en su PDF una tabla y detal1 answer -
P W = 250 lb μs = 0.32 uk = 0.21 2 a) Use una regla para preparar el diagrama de cuerpo libre (FBD) de la situación mostrada, considere todas las fuerzas que actúan en la caja. Incluya este diagram1 answer -
15 cm 5 cm 10 cm 5 cm (a) Determine la ubicación de la coordenada horizontal del centroide de área mostrada (xc con dos lugares decimales), prepare en su PDF una tabla y detalle el cálculo de los c1 answer -
& Moving to the next question prevents changes to this answer. stion 1 35 points S 15 cm 5cm 3cm 6cm 12 cm 12 cm 9cm Determine la ubicación de las coordenadas del centroide de área mostrada (xe & ye1 answer -
1,000 lb 300 lb/ft E 35,000 lb-ft 20 ft (a) Prepare un diagrama de cuerpo libre (FBD) y determine las reacciones en al apoyo fijo de la viga. (10%) (b) Use una regla para preparar el diagrama de fuerz1 answer -
LI- 15 cm 5 cm 10 cm 5 cm (a) Determine la ubicación de la coordenada horizontal del centroide de área mostrada (xc con dos lugares decimales), prepare en su PDF una tabla y detalle el cálculo de l1 answer -
A) Prepare a Free Body Diagram. and determine de reactions on the fixed support of the beam. B) Use a ruler to prepare a force diagram to indicate the location and the maximum value of this force. c)
400 lb 100 lb/ft 5,000 lb-ft 10 ft (a) Prepare un diagrama de cuerpo libre (FBD) y determine las reacciones en al apoyo fijo de la viga. (10%) (b) Use una regla para preparar el diagrama de fuerza cor1 answer -
3,900 lb 300 lb/ft 6,000 lb-ft 30 ft (a) Prepare un diagrama de cuerpo libre (FBD) y determine las reacciones en al apoyo fijo de la viga. (10%) (b) Use una regla para preparar el diagrama de fuerza c1 answer -
a) Prepare a free-body diagram (FBD) and determine the reactions at the fixed support of the beam. (10%) (b) Use a ruler to prepare the shear force diagram (lb without decimals), indicate on the d
3,900 lb 300 lb/ft 6,000 lb-ft 30 ft (a) Prepare un diagrama de cuerpo libre (FBD) y determine las reacciones en al apoyo fijo de la viga. (10%) (b) Use una regla para preparar el diagrama de fuerza c1 answer -
(a) Prepare a free-body diagram (FBD) and determine the reactions at the fixed support of the beam. (10%) (b) Use a ruler to prepare the shear force diagram (Ib without decimals), indicate on the diag
1,000 lb 300 lb/ft E 35,000 lb-ft 20 ft (a) Prepare un diagrama de cuerpo libre (FBD) y determine las reacciones en al apoyo fijo de la viga. (10%) (b) Use una regla para preparar el diagrama de fuerz1 answer -
1,000 lb 300 lb/ft 35,000 lb-ft 20 ft (a) Prepare un diagrama de cuerpo libre (FBD) y determine las reacciones en al apoyo fijo de la viga. (10%) (b) Use una regla para preparar el diagrama de fuerza1 answer -
a) Use a ruler to prepare a Free Body Diagram of the situation. Consider all forces acting on the box. b) Determine the minimum value of P required to move the box. c) Determine the value of the force
Click Submit to complete this assessment. stion 3 35 points P W 500 lb us= 0.32 uk = 0.21 2 a) Use una regla para preparar el diagrama de cuerpo libre (FBD) de la situación mostrada, considere todas1 answer -
3,900 lb 300 lb/ft 6,000 lb-ft G 30 ft (a) Prepare un diagrama de cuerpo libre (FBD) y determine las reacciones en al apoyo fijo de la viga. (10%) (b) Use una regla para preparar el diagrama de fuerza1 answer -
15 cm + 5 cm 10 cm 5 cm a) Determine la ubicación de la coordenada horizontal del centroide de área mostrada (xc con dos lugares decimales), prepare en su PDF una tabla y detalle el cálculo de los1 answer -
Int w SHIPPI PLAY (4 A gast COMPO pred a mappa e iz prokuror ay pa upang m g) con CONTA DE TITË gjate kangas va HOD menga WRESPRONCE My G& Question esame sebote a0 answers -
Fill in the missing data in the table.
Puntom, kg/s P, kPa 1 75,6 7240 2 6900 3 62,874 345 4 310 5 7 6 6,65 7 415 35 8 2,772 9 4,662 310 35 10 11 12 8,064 380 345 13 330 14 345 15 4,662 965 16 7930 965 17 18 19 1386 7580 7240 20 7410 21 730 answers -
A multifunctional bar is applied two forces of 400N at the support points. It is required to calculate bolt reactions and failures by bolt analysis method or bending failure according to the data shee
A 360 ) 400N 4 Fz č 4000 - 360 min 4 NH +++ A 590 mm 1-130- mm 465 613 mm 424 mm 43 a _ Y Trosim 390.m 180mm 103 A Nombre Fase en STP Densidad Resistencia a la tracción Límite de elastacidad Módu0 answers