Mechanical Engineering Archive: Questions from May 12, 2022
-
1 answer
-
V. Determine la ubicación del centroide o eje neutro (en in) de la sección para la dirección vertical. (15 pts.) lin & + Xg 18 in K* Sin 9 in0 answers -
Translated: Draw the shear and moment diagram, indicate the values of the maximum positive and negative, also indicate the values with each change of slope. Don't forget to include the un
III. Dibuje el diagrama de cortante y momento, indique los valores de los máximos positivos y negativos, también indique los valores con cada cambio de pendiente. No olvides incluir las unidades en1 answer -
Translated: An embedded beam has a concentrated end load that generates a moment, M4. Determine the normal stress generated at point A (in MPa), indicate whether this is a compression or tension stre
IV. Una viga empotrada tiene una carga concentrada en el extremo que genera un momento, M4. Determine el esfuerzo normal que se genera en el punto A (en MPa), indique si este es un esfuerzo en compres1 answer -
Draw the shear and moment diagram, indicate the values of the positive and negative maximums, Also indicate the values with each slope change. Don't forget to include the units in the Identification
II. Dibuje el diagrama de cortante y momento, indique los valores de los máximos positivos y negativos, también indique los valores con cada cambio de pendiente. No olvides incluir las unidades en l1 answer -
x5=6in
V. Determine la ubicación del centroide o eje neutro (en in) de la sección para la dirección vertical. (15 pts.) & luin * Xg 18 in Sin 9 in1 answer -
Translated: Draw the shear and moment diagram, indicate the values of the maximum positive and negative, also indicate the values with each change of slope. Don't forget to include the un
II. Dibuje el diagrama de cortante y momento, indique los valores de los máximos positivos y negativos, también indique los valores con cada cambio de pendiente. No olvides incluir las unidades en l1 answer -
Draw the shear and moment diagram, indicate the values of the positive and negative maximums, Also indicate the values with each slope change. Don't forget to include the units in the Identification
III. Dibuje el diagrama de cortante y momento, indique los valores de los máximos positivos y negativos, también indique los valores con cada cambio de pendiente. No olvides incluir las unidades en1 answer -
A recessed beam has a concentrated load at the end that generates a moment, MA. Determine the normal stress that is generated at point A (in MPa), indicate if this is an effort in Compression or ten
IV. Una viga empotrada tiene una carga concentrada en el extremo que genera un momento, Me Determine el esfuerzo normal que se genera en el punto A (en MPa), indique si este es un esfuerzo en compresi1 answer -
Determine the location of the centroid or neutral axis (in) of the section for the vertical direction.
Determine la ubicación del centroide o eje neutro (en in) de la sección para la dirección vertical. (15 pts.) lin 다 F1 = 5824 lb F2= 2485 lb W3= 5 kN/m M4= 58 Ib X5= 5 in 118in Sin ain1 answer -
I need help I this problem. An embedded beam has a concertrated charge that gives at the end tha generates an moment M4. Determine the normal stress generated at point A (in Mpa).Then indicate if this
Una viga empotrada tiene una carga concentrada en el extremo que genera un momento, Ma. Determine el esfuerzo normal que se genera en el punto A (en MPa), indique si este es un esfuerzo en compresión1 answer -
Considere el sistema de polea y collarin que apoya una caja con peso W = 40 lbs. Los parámetros geométricos son los siguientes: m=3, n = 2 y a=63 Se provee el diagrama de cuerpo libre de la polea y1 answer -
borre mis calculos erronios para que se vea mejor
a Una fuerza 7 = 196 N es aplicada a la barra AB como se muestra. Los parámetros geométricos son a = 29 cm, b = 41 cm y c = 44 cm. Tenga en cuenta que es posible que la figura no esté dibujada a es1 answer -
0 answers