Mechanical Engineering Archive: Questions from May 02, 2022
-
Considering the following piece to be manufactured in CNC-HASS, what is the value of U in P1 to P2? Note: The chisel cuts through the top of the piece
Pregunta 3 10 pts Considerando la siguiente pieza para fabricarse en CNC-HAAS ¿cuál es valor de U de P1 a P2? NOTA: el buril corta por la parte superior de la pieza. 4.600 P7 1.875 125 x 45 P3 5.0001 answer -
Determine las temperaturas T1 a T9, resuelva por el método numérico que mas le complazca. 100°C T1 T2 50°C 75°C T4 T7 T5 T8 0°C T3 T6 T91 answer -
Determine the minimum normal force needed to hold a 5-pound part with a coefficient of friction of 0.7. (see figure).
2. Determine la fuerza normal mÃnima necesaria para mantener una pieza de 5 libras con un coeficiente de fricción de 0.7. (ver la figura). ue1 answer -
The tongs of a gripper (parallel) apply a 54-N normal force to each side of a piece of iron. If the coefficient of friction is 0.85, calculate the maximum weight, in pounds, that could be lifted witho
3. Las pinzas de un gripper (paralelo) aplican una fuerza normal de 54-N a cada lado de una pieza de hierro. Si el coeficiente de fricción es 0.85, calcular el pero máximo, en libra, que se podrÃa1 answer -
Determine the minimum normal force on the gripper shown in the figure to hold a 15-pound part without slipping when a robot accelerates upwards vertically at a rate of 0.75 feet per second squared. Th
4. Determine la fuerza normal mÃnima del gripper que se muestra en la figura para mantener una pieza de 15 libras sin que se resbale, cuando un robot acelera hacia arriba en forma vertical a un rate1 answer -
What amount of pressure does a parallel grip gripper with a contact area of ​​0.75 in² force that need to apply if acting on the contact surface is 35 pounds?
5. Que cantidad de presión necesita realizar un gripper de agarre paralelo con un área de contacto de 0.75 plg² si la fuerza que actúa en la superficie de contacto es de 35 libras.1 answer -
1. Del siguiente gráfico, determine: 1.1. el esfuerzo de cedencia 1.2. módulo de elasticidad 1.3. modulus of resilience 1.4. deformación permanente 1.5. sà una pieza se cargó hasta un esfuerzo de1 answer -
Yielding effort. module of elasticity modulus of resilience permanent deformation If a part was loaded with a stress of 44 ksi and then unloaded,determine set in terms of strain.
1. Del siguiente gráfico, determine: 1.1. el esfuerzo de cedencia 1.2. módulo de elasticidad 1.3. modulus of resilience 1.4. deformación permanente 1.5. sà una pieza se cargó hasta un esfuerzo de1 answer -
Determine this grafic for the module cut.
2. Determine del siguiente grafico el modulo de corte. T (MPa) 130 0.005 y (rad)1 answer -
6. Una viga empotrada en un extremo es sometida a una fuerza normal N = 50 kips, determine la elongación. (largo = 20 ft, área = 5 in² y E = 29,000 ksi) +N +81 answer -
7. Una barra empotrada en su extremo A, tiene una fuerza de 100 kN en el punto B y otra fuerza de 20 kN en el punto C. Determine la elongación o contracción en la barra AC. (A = 0.0035 mm2, E = 2001 answer -
11. Determine el momento polar de inercia para una sección circular solida de con diámetro de 1.5 in y para un tubo de 0.2 in de espesor con diámetro exterior de 3 in. 12. Una barra de acero con di0 answers -
If the cross section of the femur at section a-a can be approximated as a circular tube as shown, determine the security factor developed on the critical point on the cross section at the section a-a
Cuadro 1. Propiedades mecánicas a tracción (Tejido Óseo) Unidades Propiedad Resistencia última Esfuerzo de fluencia Magnitud 76.6 MP 69.2 MP 7.7 GPâ‚‚ 0.8 % Módulo de elasticidad Deformación elÃ1 answer -
The constant angular velocity of link 1 is 100 rad/s. determine: a) The angular velocity of link 2 b) the speed of the piston c) speed of point c angle 35 grades
La velocidad angular constante del eslabón 1 es de 100 rad /seg. Determine: a) La velocidad angular del eslabón 2. La velocidad del pistón. b) c) Velocidad del punto C 4 cm MA AB 7 cm. AC = 5,5 cm1 answer -
SRPSRAPP perpendicular Arbowego for 10 20 ore Trees C. E parallel saya Eperpendicutat Vergers are constamment en el cora. E. te M0 answers -
1 answer