Mechanical Engineering Archive: Questions from June 05, 2022
-
In the following problems, assume that the bending stiffness El of each beam is constant. 9.1 to 9.3 For the loading shown in the figures, determine a) the equation of the elastic curve for the cantil
En los siguientes problemas suponga que la rigidez a flexión El de cada viga es constante. 9.1 a 9.4 Para la carga mostrada en las figuras, determine a) la ecuación de la curva elástica para la vig2 answers -
11.24 to 11.26 Determine the strain energy of the prismatic beam AB for the loading shown in the figure. Consider only the effect of normal stresses.
11.24 a 11.27 Determine la energía de deformación de la viga prismática AB para la carga que se muestra en la figura. Considere sólo el efecto de los esfuerzos normales. 10 W A B B L Figura P11.251 answer -
11.83 and 11.84 For the prismatic beam shown in the figure, determine the deflection at point D.
11.83 y 11.84 Para la viga prismática que se muestra en la figura, determine la deflexión del punto D. 11 n tel 10 A D B D B |12_12_ 1 -L/2- L/2 L/2- -L/2- Figura P11.83 y F Figura P11.84 y P¹¹0/1 answer -
1 answer
-
3-The figure shows the scheme of the experimental prototype used to carry out head loss tests in a pipe through which hydrogen flows at 20 °C, Assuming that there is a flow of 7000 L/min and that the
3.- En la figura se muestra el esquema del prototipo experimental utilizado para hacer pruebas de pérdida de carga en una tubería por la que fluye hidrógeno a 20 "C. Suponiendo que se tiene un fluj1 answer -
1.- En el esquema de la figura, considere que todos los fluidos se encuentran a una temperatura de 20ºC. Determine la presión manométrica y absoluta en psf en el punto A. (2 pts) Water Oil, SG=0.851 answer -
2.- In the system shown in the figure, consider that all the fluids are at a temperature of 20 °C. The pressure in section 2 is 180 kPa and the diameters of sections 1 and 2 are 8 cm and 5 cm, respec
2.- En el sistema que se muestra en la figura, considere que todos los fluidos se encuentran a una temperatura de 20 °C. La presión en la sección 2 es de 180 kPa y los diámetros de las secciones 11 answer -
The velocipede illustrated is traveling 20.8 mph to the left and accelerating in the same direction at a rate of 7.8 ft/s2. The front wheel has a diameter of 50 inches, and the rear wheel has a diamet
El velocípedo que se ilustra viaja a 20.8 mph hacia la izquierda y acelera en la misma dirección a razón de 7.8 pie/s². La rueda delantera tiene un diámetro de 50 pulgadas, y la rueda trasera tie1 answer -
1 answer
-
If the block at C is moving downward at 16 ft/s, determine the angular velocity of bar AB at the instant θ = 29º.
Si el bloque en C se mueve hacia abajo a 16 pies/s, determine la velocidad angular de la barra AB en el instante en que 0 = 29⁰. 3 ft VC 8 WAB -2 ft B1 answer -
The OP arm joins the two rotating discs without slipping between them. The large disk, of radius R = 35 cm, rotates about point O with angular velocity ωR = 31 rad/s clockwise. For its part, the arm
El brazo OP une los dos discos que rotan sin deslizarse entre ellos. El disco grande, de radio R = 35 cm rota respecto al punto O con velocidad angular R = 31 rad/s en sentido horario. Por su parte, e1 answer -
WhatsApp X ASIGNACIÓN I CONCENTRACIÓN X + ← → C Ⓒ Archivo | C:/Users/roberto%20acosta%20arita/Downloads/ASIGNACIÓN%201%20CONCENTRACIÓN%20DE%20TENSIONES%20Y%20ESFUERZOS%20NORMALES%... L ASIGN0 answers -
Ejemplo Determine el(los) valor(es) de λ que hacen cero el determinante de la matriz: 2-A 0 0 A = 3-A 1-A 0 1 Introducción Determinante 2×2 Ejemplo Regla 1 Geometria 1 Ejemplo Determinante 3x3 Regl1 answer -
Materiales de Ingenieria
Español Se realiza un ensayo de dureza Brinell a una pieza de un material desconocido se sabe que el diámetro de la bola es de 2.5 mm y la fuerza aplicada es de 500kg, la dureza del material fue de1 answer