Mechanical Engineering Archive: Questions from July 04, 2022
-
Determine the radius of gyration at y of the shaded area shown with respect to the y-axis, when a=111.848 in and h=138.444 in.
Determine el radio de giro en y del área sombreada que se muestra con respecto al eje y, cuando a=111.848 in y h=138.444 in 3+1 T h h ↑ a Criterios de conformidad: 1. Reporte el radio de giro en y.1 answer -
For the piping system shown in the figure (L1=1000 ft, d1= 12 in; L2=1500 ft, d2= 8 in; L3=800 ft, d3= 12 in; L4=1200 ft, d4= 15 in) , all pipes are concrete with a roughness of 0.04 in. Neglecting mi
Para el sistema de tuberías mostrado en la figura (L₁=1000 ft, d₁= 12 in; L₂=1500 ft, d₂= 8 in; L3=800 ft, d3= 12 in; 44=1200 ft, d₂= 15 in), todas las tuberías son de concreto con una rug3 answers -
Water at 20°C is to be pumped through 2073 ft of pipe from Reservoir 1 to Reservoir 2 at a rate of 2.6 ft3/s, as shown in the figure. If the pipe is 6-inch-diameter cast iron and the pump has an effi
Se va a bombear agua a 20°C a través de 2073 pies de tubería, desde el depósito 1 al 2, a un caudal de 2.6 ft³/s, como se muestra en la figura. Si la tubería es de hierro fundido de 6 pulgadas d1 answer -
The tank-pipe system shown in the figure (H=4.4 m, h=1.6 m, L=4.8 m, d=3 cm) must deliver at least 11.2 m3/h of water at 20°C to the reservoir. What is the maximum allowable roughness ε for the pipe
El sistema tanque-tubería mostrado en la figura (H=4.4 m, h=1.6 m, L=4.8 m, d=3 cm) debe entregar al menos 11.2 m³/h de agua a 20°C al depósito. ¿Cuál es la rugosidad máxima permisible para la1 answer -
The system in the figure consists of 1,076 m of 63-mm diameter cast-iron pipe, three 90° threaded elbows, two 45° threaded elbows, a half-closed gate valve, and a sharp outlet to the reservoir. If t
El sistema de la figura consta de 1076 m de tubería de hierro fundido de 63 mm de diámetro, tres codos roscados de 90°, dos codos roscados de 45, una válvula de compuerta cerrada a la mitad y una1 answer -
Oil (SG = 0.81) leaves the pipe, as shown in the figure, with a flow rate Q=38 ft3/h. If L=6 ft, D=0.41 in, and h=10 ft, what is the kinematic viscosity of the oil in ft2/s, assuming laminar flow?
Aceite (SG = 0.81) sale de la tubería, como se observa en la figura, con un caudal Q=38 ft³/h. Si L=6 ft, D=0.41 in y h=10 ft, ¿cuál es la viscosidad cinemática del aceite en ft³/s, si se asume3 answers -
A reservoir (z1=36 m) supplies water at 20 °C through 105 m of 0.3 cm diameter cast-iron pipe to a turbine (z2=3 m), which draws 84 HP of effective hydraulic power. The water then escapes into the at
Un embalse (Z₁ = 36 m) suministra agua a 20 °C a través de 105 m de tubería de hierro fundido de 0.3 cm de diámetro a una turbina (Z₂-3 m), la cual extrae 84 HP de potencia hidráulica efectiv1 answer -
Given the parameters (U, L, g, ρ, μ) that affect a certain flow problem in liquids, the relation V^2/(Lg) a. speed head b. impact energy c. Froude number d. Bernoulli's head and. Kinetic energy
Dados los parámetros (U, L, g, p, μ) que afectan a cierto problema de flujo en líquidos, la relación V² Lg es usualmente conocida como: O a. Cabeza de velocidad O b. Energía de impacto О с. N1 answer -
Determine the reactions at the roller support li of the beam shown in the figure, after Ditute the shear force and moment diagrams. Et is constant. Use Overlay of elected
Determine las reacciones en el soporte de rodillos B de la viga mostrada en la figura, despué dibuje los diagramas de fuerza cortante y de momento. El es constante. Usar Superposició de efectos (5 p1 answer -
0 answers
-
A particle travels along a straight line at a speed of v = (20-0.05s^2)m/s, where s is in meters. Determine the acceleration of a particle when s=15m.
F12-8. Una partícula viaja a lo largo de una línea recta a una velocidad de v= (20 0.05s2) m/s, donde s está en metros. Determine la aceleración de la partícula cuando s = 15 m.3 answers