Mechanical Engineering Archive: Questions from April 09, 2022
-
1 answer
-
5) A plane wall with a thickness of 21 and thermal conductivity k experiences a uniform generation of heat. Considering the steady state, determine the expression for the temperature variation inside
5) Una pared plana con un espesor de 2L y conductividad térmica k experimenta una generación uniforme de calor. -L Considerando el estado estacionario determinar la expresión para la variación de1 answer -
1 A conducting wire with a diameter of Imm and a length of 10 m is wrapped in a 2-mm-thick plastic coating whose thermal conductivity is 0.15 W/te. The potential difference between the ends of the wir
4) Un alambre conductor de 3mm de diámetro y 10 m de largo está envuelto con una cubierta de plástico de 2 mm de grosor cuya conductividad térmica es 0.15 W/mºc. La diferencia de potencial entre1 answer -
5) A 2m x 15m wall section of an industrial furnace in which the temperature is measured on the outer surface of this section, which turns out to be 110'C. The temperature of the room where the furnac
5) Una sección de pared de 2 m x 1.5 m de un horno industrial en el que se quema gas natural no está aislada y se mide la temperatura en la superficie exterior de esta sección, lo cual resulta ser1 answer -
6)1Show that the critical radius for a spherical shell is given by p where k is the thermal conductivity of the insulation and hes the convective heat transfer coefficient on the outer surface of the
6) Muestre que el radio crítico para una capa esférica esta dado por: 2k Ter.esh donde k es la conductividad térmica del aislamiento y h es el coeficiente de transferencia de calor por convección1 answer -
A square plate 100 mm (4 in) thick and a circular right cylinder with a radius of 100 mm (4 in) and a height of 50 mm have the same volume. If you are going to melt each one of them using a cylindrica
Problema 1 Una placa cuadrada de 100 mm (4 pulgadas) de espesor y un cilindro recto circular con un radio de 100 mm (4 pulgadas) y una altura de 50 mm tienen el mismo volumen. Si se va a fundir cada u1 answer -
The cast iron spool in the following photograph has the dimensions shown on it. Without considering the holes in the flange, and that the faces of the flanges are machined, Set the dimensions of the m
Problema 2 El carrete de hierro fundido de la siguiente fotografía tiene las dimensiones mostradas sobre el mismo. Sin considerar los agujeros en la brida, y que las caras de las bridas son maquinada1 answer -
A spherical cast iron cap (density 7.87 g/cm3), in sand mold (density tamped sand 1700 Kg/m3), with the dimensions and configuration shown in the next figure. Determine if it is necessary to overweigh
Problema 3 Se producirá un casquete esféricos de hierro fundido (densidad 7.87 g/cm3), en molde arena (densidad arena apisonada 1700 Kg/m3), con las dimensiones y configuración mostradas en la sigu1 answer -
Se hace incidir luz de longitud de onda de 7,2 nm sobre un material con función de trabajo 20 ev. La energía cinética máxima de los electrones eyectados del materia es: O a. 152,19 eV O b. No se l1 answer -
Suppose that the kinetic energy of a system is written as and the potential is a) Find the Euler Lagrange equations for this system. b) Find the units of K so that this problem could make physical se
Problema 2 Suponga que la energía cinética de un sistema se escribe como 1 T = K04 (1) 2 y que el potencial es V = 3922 = (2) a) Encuentre las ecuaciones de Euler Lagrange para este sistema. b) Encu1 answer -
match
0 02 02 b k2 Hrin a k1 L mi m2 ſa1 a2 La3 a4) Vë a21ſë 16.3+ d1 b1 + Lb3 b21011 b4 62] Ce;} = (az) = al - Kia² a4 m2 L2 b1 b3 b4 d1 mi L2 D F Ki a2 + m2 g L + K2b2 'o - K2 62 Ky a2 + K2 62 mı1 answer -
0 answers
-
Consider a particle moving in one dimension under the action of the potential. a) Draw the potential for different representative values of b. b) Find the values of b for which there are minima in the1 answer -
EXCERSICE (English Version) A plate cam mechanism with reciprocating radial follower is required, for three stages of rest, to bring the follower from 0 to 63 mm in 40° of cam rotation, then the foll0 answers