Electrical Engineering Archive: Questions from October 27, 2023
-
Draw the small AC equivalent circuit.
Find \( R_{o 2}, R_{i n}, A_{v T}=\frac{v_{02}}{v_{i n}} \) of the folowing FET - FET Cascade amplifier.1 answer -
ayuda para obtener lck en nodos y lvk en mallas
PDentificar nodos A plicar LCK nODOS Aplicar LVK Malla1 answer -
PROBLEMA NÚM. 3 (25\%) Para la figura que se muestra detemine la coordenada en " \( y^{*}( \) y) del centroide del área compuesta sombreada, \( (30 \%) \)1 answer -
ilustrar si hay reduccion de circuito
1. Dado el circuito de la siguiente figura: 1.1. (3 puntos). Obtenga el circuito equivalente de Thévenin, entre los puntos \( \boldsymbol{a} \) y \( \boldsymbol{b} \), del circuito dado. 1.2. (1 punt1 answer -
a. The elements of the amplifier shown in the figure obtain the following values: Vs = 100 mV, R1 = 71.7 Ω, C1 = 2.9 µF, R2 = 284.3 Ω, Av1 = -29.6, R3 = 12.4 kΩ, C2 = 191.0 nF, R4 = 13.2 kΩ,
Los elementos del amplificador mostrado en la figul ichen los siguientes valores: \( \mathrm{Vs}=100 \mathrm{mV}, \mathrm{R} 1=71.7 \Omega, C 1=2.9 \mu \mathrm{F}, \mathrm{R} 2=284.3 \Omega, A v 1=-290 answers -
El transistor de circuito mostrado opera en la elementos del circuito tienen los siguientes valores: de corte alta debido a la salida del circuito es: 7 points Notas: - Notar el uso de prefijos en cad0 answers -
1. La frecuencia de corte neta debido a estos capacitores es: 2. Justamente por debajo de esta frecuencia de corte neta, la banda de transición es - Notas: - Notar el uso de prefijos en cada respuest0 answers -
El bypass capacitor a. es otro nombre para el coupling capacitor b. deja pasar señales dc c. no permite que disminuya la ganancia de voltaje d. estabiliza el circuito en dc e. provee aislación dc1 answer -
Al aplicar el teorema se Miller se reemplazan toda las impedancias que están conectadas desde la entrada a ground de un amplificador a. cierto b. falso Podemos aumentar el ancho de banda (bandwidth)1 answer -
\( =15.2 \mathrm{k} \Omega, C 2=117.0 \mathrm{nF}, \mathrm{R} 4=10.8 \mathrm{k} \Omega, \mathrm{Av} 2=42.1, \mathrm{R} 5=179.2 \Omega, \mathrm{C} 3=16.9 \mu \mathrm{F} \) y \( \mathrm{R} 6=247.0 \Omeg1 answer -
A frecuencias altas, un amplificador que tiene la configuración de base común: a. tiene el efecto de Miller solamente en su entrada b. tiene el efecto de Miller tanto en su entrada como en su salida1 answer -
Idealmente el upper cutoff frequency debe ser cero. a. cierto b. falso Si tenemos un amplificador de base común, la frecuencia de corte baja se debe a: a. Capacitores de acople solamente b. Capa1 answer -
In the laboratory we have measured the cutoff frequencies of a certain amplifier and it turns out that they are: 100 Hz and 40 kHz. The power in midband was also measured and its value is as follows:
el laboratorio hemos medido las frecuencias de corte de cierto amplificador y resulta que las mismas son: \( 100 \mathrm{~Hz} \) y \( 40 \mathrm{kHz} \). También se midió la potencia en midband y su1 answer -
1 answer
-
Notas: - El bate de fórmulas se encuentra en el documento anejado: Fórmulas Respuesta en Frecuencia.pdf vcc0 answers -
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
1 answer
-
Determinar i en el circuito de la figura
\( 1.9704 \cos \left(10 t+5.65^{\circ}\right) \mathrm{A} \)1 answer -
1 answer
-
1 answer
-
hacer simulacion resolviendo los circuitos . calculando la corriente medida y corriente calculada de cada una de las resistencias en los circuitos
Duración: 1 seside de 2 horas Introducelon Los teoremas de Thevenin y Norton permiten la simplificación de los circuitos y su analisis pensando en terminos de la carga. Objetivo: que el estudiante a1 answer -
armar los siguientes circuitos para obtener las siguientes graficas . llenar la siguiente tabla en cada uno de los circuitos
3. Calcular los valores de voltaje y corriente en carga y descarga del capacitor, hacer las gráficas necesarias 4. Hacer un barrido de valores para el capacitor y comprobar los valores de carga0 answers -
Para el siguiente filtro activo R1 = 10KW, R2 = 110KW, R = 5KW y C = 2nF. Determine: a(La función de transferencia AV(s) = Vo(s)/Vi(s), b)La máxima ganancia de voltaje en dB en la banda de pas
Para el siguiente filtro activo \( R_{1}=10 \mathrm{KW}, R_{2}=110 \mathrm{KW}, \quad R=5 \mathrm{KW} \quad \) y \( C=2 \mathrm{nF} \). Determine: a) La función de transferencia \( A_{\mathrm{V}}(s)=1 answer -
1 answer
-
1 answer
-
0 answers
-
Determine Q for each diodo. Von=o.65V
3. Determine \( Q \) para cada diodo. Considere diodos de silicio con \( V_{O N}=0.65 \mathrm{~V} \). Figura 3. Problema 3.1 answer -
4. The diode in figure 4 has VON =0.7 V. Determine the appropriate resistors R1 and R2 to meet the following conditions: the diode must be on for 5V<=Vps<=10V, the minimum current in the diode m
4. El diodo de la figura 4 tiene \( V_{O N}=0.7 \mathrm{~V} \). Determine las resistencias \( R_{1} \) y \( R_{2} \) apropiadas para cumplir las siguientes condiciones: el diodo debe estar encendido p1 answer -
0 answers
-
0 answers
-
1 answer
-
0 answers
-
1 answer
-
1 answer
-
1 answer
-
1 answer