Civil Engineering Archive: Questions from April 23, 2023
-
Problema: Prepare un estimado detallado del costo de construir la pared que se ilustra a continuación. El terreno es tierra común, es llano y la parte inferior de la zapata se colocará a 2.0' por d0 answers -
A manometer is used to measure the pressure in a tank. The fluid being used has a specific gravity of 0.75 and the elevation of the column in the manometer is 55 cm, as shown in the figure. If the loc
Problemas de Hidrostática 1. Se utiliza un manómetro para medir la presión en un tanque. El fluido que se utiliza tiene una gravedad específica de 0.75 y la elevación de la columna en el manómet2 answers -
Calculate by hand the hydrostatic thrust and the center of pressure (yk) on the slide gate of an intake work in a diversion dam like the one shown in the following figure. The gate has a width b = 2m.
2. Calcular a mano el empuje hidrostático y el centro de presiones (yk) sobre la compuerta deslizante de una obra de toma en una presa derivadora como la mostrada en la siguiente figura. La compuerta2 answers -
3) Determine the hydrostatic pressure and its center of pressure on the curved surface of the wall shown in the figure. Likewise, determine the resulting hydrostatic angle 4) For a construction projec
3. Determinar el empuje hidrostático y su centro de presión sobre sobre la superficie curva del muro mostrado en la figura. Asi mismo, determinar el ángulo \( \theta \) del empuje hidrostático res2 answers -
The open tank in the figure contains water at 20ºC and is being filled through the pipe in section 1 with a V1= 3m/s and also through the pipe in section 3 with Q3 = 0.01 m3/s. If the water level, h,
1. El tanque abierto de la figura contiene agua a \( 20^{\circ} \mathrm{C} \) y se está llenando mediante el tubo de la sección 1 con una \( V_{1}=3 \mathrm{~m} / \mathrm{s} \) y también mediante l2 answers -
2) What diameter is required in a pipe with Ɛ=0.2mm and a length of 2450m, if it is desired to transport a rate of 1.10m3/s and the allowed energy loss is 2.45m? 3) A steel pipe (Ɛ = 0.3mm) transpor
2. ¿Qué diámetro se requiere en una tubería con \( \varepsilon=0.2 \mathrm{~mm} \) y una longitud de 2450 \( \mathrm{m} \), si se desea que transporte un gasto de \( 1.10 \mathrm{~m}^{3} / \mathrm2 answers -
0 answers
-
0 answers
-
0 answers
-
1 answer
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
1 answer
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
4) In the system shown, calculate the theoretical diameter required to transport a rate Q=150l/s. The pipeline has devices installed such that in sum they give K = 8. You can use the App, TI or Moody
En el sistema mostrado, calcule el diámetro teórico requerido para transportar un gasto \( Q=150 \mathrm{l} / \mathrm{s} \). La tubería tiene una rugosidad absoluta de \( \boldsymbol{\varepsilon}=\2 answers -
0 answers
-
0 answers
-
0 answers
-
1 answer
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
0 answers
-
1 answer
-
0 answers